Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> 1970 chevelle engine wiring
User Name
Password
lost password?   |   register now

Thread: 1970 chevelle engine wiring Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-27-2013 07:25 PM
crownver Oops! Meant to post this in your other thread.
01-27-2013 07:24 PM
crownver If it's a stock floor shift set up, I would thing that there'd be a purple wire with white stripe to where the shifter would be if you had one. Also should be a purple wire there. Those are the ones I meant for you to jump, while turning the key to start.
01-22-2013 03:47 AM
EOD Guy Depending on what was done before you got it...... One large cable to the battery, purple wire from the ing, yell or off white to the coil. The other wire you see on the dia is the braided wire that runs from the soleniod to the actual starter motor.

Earlier in the post someone wrote that the resistance wire is so that the points won't burn up if you left your key on etc...... maybe true but......... The resistance wire is so you won't burn up your coil.
01-21-2013 08:13 PM
Vincentnova should i have two red cables at the starter , i mean cable from the battery and one more

beside the big purple i dont have any more 10ga cable
01-19-2013 05:51 AM
timothale
Gm wiring

for some dumb reason GM repeated the same colors, but used different wire sizes for different things, I had Elect systems for a while when I was an engineer at Ford. We used to say the GM guys only had an 8 crayon box when they were a kid, and didn't know about more colors or wires with color stripes.
01-18-2013 10:44 PM
alittle1
Quote:
Originally Posted by Vincentnova View Post
thanks for the diagram

yes i have point

on the diagram the resistance wire its white orange purple ?
all those color together on one wire ?
It can be any one of those colors because this is a wirng diagram used over a period of years, not just 1970. I have white wires on 3 1970 Chevelles and the wire inside is a bright silver 16 gauge resistance wire.
12-27-2012 11:32 PM
gearheadslife the 70 velle has a res. wire to coil..if running hie you have to bypass it..
as it drops volts to around 9v

I most times tap into the wire at the firewall bulkhead connector.. soldering in a splice.. leaving the old wire intact..
run the new wire and tape up the old one and wiretie it..
if your hei /etc fails you can drop the points dissy back in and untape the wire and down the road you go.. this is a plus with the drop in electric conversions.. as when they fail you just drop the points back in and go..
and murphy's law is because you have a back up. you'll never need it..
12-27-2012 10:30 PM
cobalt327
Quote:
Originally Posted by crownver View Post
I thought if you had points you need a resistor to keep the points from burning.
You do. GM went to a resistance wire needed for the points-type ignition system, instead of using a ballast-type resistor.

Whether a resistor (wire or otherwise) is needed or not depends on the type of ignition system being used and the coil resistance.
12-27-2012 07:03 PM
1971BB427
Quote:
Originally Posted by crownver View Post
I thought if you had points you need a resistor to keep the points from burning.
Only if you leave your ignition on when the engine isn't running, and the points are in the perfect situation to try and fire. The reason Chevy went to an "acc." position on their key switch was to stop frying points. It brings on the system without giving power to the coil.
I've run a lot of 60's and 70's Chevys without a resistor and not burnt up points. Not running a resistor in my 327 powered gasser now, or my 427 powered Camaro, and no issues.
12-27-2012 03:54 PM
crownver I thought if you had points you need a resistor to keep the points from burning.
12-27-2012 03:54 PM
Vincentnova ohhh thanks its all i needed

thanks a lot
12-27-2012 03:05 PM
1971BB427 There's a pretty easy way to check. Put a test light on one of the wires and then turn the key on. If it lights up it has 12 v. Then turn the key to the start position and see if it stays lit up. If it doesn't, then move to the next wire. The ignition will turn on power to the coil, but will interrupt power to other items when the key is turned to the "start" position.
12-27-2012 02:57 PM
Vincentnova yes but still.... i still doesnt know wich cable go to the + at the coil
the color doesnt match the diegram

any suggestion?
12-27-2012 02:51 PM
1971BB427
Quote:
Originally Posted by crownver View Post
Here's a couple more diagrams that may be easier to read. If you still have points you'll need 2 wires to the coil, one with a resistor in the circuit.
didn't Chevy drop the inline resistor before 1970?
12-27-2012 02:33 PM
Vincentnova thanks for the diagram

yes i have point

on the diagram the resistance wire its white orange purple ?
all those color together on one wire ?
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.