Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> 72 chev p u windsheild rust
User Name
Password
lost password?   |   register now

Thread: 72 chev p u windsheild rust Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-03-2013 05:28 PM
AFX Be very careful to spot weld and not run a bead. Spread your spots about 2" apart then go back and fill inbetween with the same 2" spread. Hammering the metal into position as you go," It's better to have the metal too high so you can beat it down". Take your time and let the metal cool between spots with either compressed air or a wet rag works best. You will warp your top if you rush it and will wish you only had a leak. Either fab a piece or cut out a different one, it's all the same, not so hard, be patient and it will be fine. I use the thinest cut off wheel I can find. I also have sand blasted with a spot blaster the infected areas and slowly built up the area with weld,"Keep it cool". Figure out what caused it also...
01-01-2013 01:08 AM
Alaska Gasser If you have access to a parts cab that is in good shape (& the price is right), the quickest and easiest would be to cut out a section of it and replace yours.
12-31-2012 10:13 PM
gearheadslife look at the trip rail.. your sealer is mostlikely leaking..
12-31-2012 09:59 PM
dogwater Take pictures first lots of pictures, use a 4 1/2 grinder w/ thin cut off wheels. Then cut only where you want to weld the new stuff to. Save what you cut off to use as a guide. Then only cut out the rusted stuff in like 6 or 8 ins. each.Don't be like me an work on it all day long, take your time,make it last a few weekends,enjoy the pain.
,
12-31-2012 09:47 PM
tech69 a shrinker/stretcher would work great for that. you can fab a piece up and shape it to the existing piece while it's still in. Whatever you do make sure you measure good,especially the depth otherwise you might have problems putting your mouldings back on.
12-31-2012 08:20 PM
OneMoreTime You can fab a piece of Z bar from 20 gauge and weld that into place replacing the rusted area..takes some metal working skills though..

Sam
12-31-2012 05:55 PM
TNCHEVYMAN
72 chev p u windsheild rust

I have a 72 chev p u. It has bad rust around the windsheild inside the cab. It is around the top at the rubber seal all the way across the top. I need A new windsheild, and the rust is so bad its going to affect the seal install. Looks like I have bad problems. No rust any where else. I have A small wire welder. I can weld pretty good. What can I do. THANKS

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:34 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.