Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Horsepower estimate for the Gen III Vortec V8
User Name
lost password?   |   register now

Thread: Horsepower estimate for the Gen III Vortec V8 Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-02-2013 10:40 PM
GunnerTHB 96-98 was Gen I Vortec, not TBI. The head casting #'s should end in 062 or 906 for the 350 and 059 or 520 for the 305. Gen III Vortec truck engines were 4.8L, 5.3L, and 6.0L.

TBI head casting # ended in 193. It makes a nice paperweight.
01-02-2013 09:38 PM
Originally Posted by Rmatt87 View Post
Never mind the truck is a 1997 Chevy C/K 2500. It comes with a 5.7L V8 that is Throttle Body injected.
As said before: No, it's not. There was no TBI 96+ Pickups, nor are 193 heads off a 96+ engine. Your top end at the very least is model year 1995 or older for a truck. You may be confused because you're getting back about as much misinformation as you're giving.
01-02-2013 08:53 PM
Rmatt87 Never mind the truck is a 1997 Chevy C/K 2500. It comes with a 5.7L V8 that is Throttle Body injected.
01-02-2013 08:45 PM
Rmatt87 Thanks to you all for the feedback. Do any of you know if i can still use this block with the same set up as listed above with a good set of aftermarket heads?
01-02-2013 08:34 PM
ap72 gen 2 is LT engines, the sbc Vortec is a Gen 1 engine. The 193 head is on a gen 1 TBI engine and as stated is good for about 300-325hp.
01-02-2013 07:45 PM
hpete You need to figure out exactly what you have. A 97 silverado came with neither an ls 1 or tbi.
01-02-2013 07:10 PM
vinniekq2 you said that you have an LS-1 engine.
Those engines are over 300 HP and fuel injected,with the GM hot cam and cleaned up cylinder heads they make over 400 HP with fuel injection.
Spend the money to make the factory FI work in your car and have an easy 400 HP engine that idles smooth and gets decent mileage,or convert to a carb and make less power?
01-02-2013 06:54 PM
Rmatt87 vinniekq2- moving backwards??
01-02-2013 06:52 PM
Rmatt87 UPDATE!!! After a quick research ive learned that i have the 64cc TBI heads. Shouldve known since the engine is a TBI. I didnt get to look for the casting number BUT by the casting marks on the outside of the head i see the double bar. says the casting num. is 193 and even has pics. This head is not recommended for high RPM performance unless serious port work is done. Anyone know what kind of port work would need to be done to make these work?
01-02-2013 06:32 PM
vinniekq2 drop that LS engine in the car as it came from the factory.After you convert to carb you should stop moving backwards
01-02-2013 06:26 PM
Rmatt87 It is a Gen III LS1 engine i believe. It was in a 1997 Chevrolet Silverado 2500 4x4. The casting numbers for this block is 14093638. After i google the casting number on the back of the block it says its a 5.7L Vortec. The heads have a 64cc chamber. The valves are 1.94/1.50 but heads are machined to accept 2.02/1.60 valves. Not sure what that means. The 9.5:1 compression is their recommendation. I thought about bumping it to 12.5:1 CR. I already have the pistons if i do the higher compression. Again im not sure if i even want that high of compression. Thanks for your response.
01-02-2013 04:51 PM
Horsepower estimate for the Gen III Vortec V8

Hey HotRodders,
I was on here earlier looking up how to build the cheap made in mexico 350 V8 and seen how big the gain in horsepower was with the ported Vortec heads, intake, and Holley carb. I realized that i have a Vortec engine thats in great shape so ive decided to build this block for my S10 V8 conversion. I was wanting to know if anyone can give me an estimate in horsepower if i use a Big Mutha Thumpr Cam from COMP Cams, ported Vortec heads, big long tube headers, Flowmaster 44 mufflers, Edelbrock Performer RPM intake manifold (Dual-plane, High rise), and a 750 CFM Edelbrock Performer Carb (calibrated for performance). The camshaft has an RPM range of 2600 to 6800 and the valve lash is listed below:

Intake Exhaust

Duration 291 311

Duration@.050" Lift 235 249

Valve Lift 0.573 0.558

Lobe Lift 0.338 0.329

I will be using the recommended kit from COMP Cams and the compression ratio recommendation of 9.5:1. I haven't decided on the type of ignition system as far as the distributor goes so if anyone has any suggestions that may work with this application feel free to let me know. I apologize for writing so much for the first time.


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 05:52 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.