Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> chevelle frame
User Name
Password
lost password?   |   register now

Thread: chevelle frame Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-12-2013 06:22 AM
deadbodyman Now the fun starts...
01-11-2013 09:09 PM
MARTINSR Cool, you are on your way to a smiling face behind the wheel.

Brian
01-10-2013 10:20 AM
jr2009 hey guys, picked the new frame up, it looks good. measured it in all the ways you all suggested. everything checked out. I've got it home now.

Thanks for the help.
01-09-2013 05:32 PM
Too Many Projects The rear springs are different between '66 and '67 too. "66 has a large coil on top and '67 has a small coil. The '66 frames did go to the '67 spring later in the production year. If you have a reputable frame shop in the area, take it to them and they can set it up and check it for twist, diamond, etc and straighten as needed. We do this where I work and a bare frame is easy to get straight, unless it is very bent.

What is so bad about yours ? Is it rust damaged or just bent ?
01-05-2013 08:18 PM
deadbodyman Crap I tried posting pics of his collection but wouldnt take anyway he has about 50 cars and almost all are 65-67 chevelles and elks a couple verts and a good bit of GTO's up to 68...kind of a wierd guy to deal with but most of my friends are...he's also got parts up the ying yang for ya...PM me and I'll give you his number..
01-05-2013 07:39 PM
deadbodyman
Quote:
Originally Posted by jr2009 View Post
Hello everyone,

I have recently discovered my frame on my 67 chevelle is beyond repairable and is also twisted, I have decided to junk it. and get a doner.

I found a guy selling a 66 frame. when I go to pick it up what should I be looking for to make sure I am getting a good straight frame? any crucial measurements to take?

any advice is greatly appreciated.

Thanks
JR
How much does he want for it ,first of all...and how rotted is it? I know a guy that has about 10 of these frames inc.convertable frames I can do all the checking for you and send you one if its feasable I might be able to get you a great deal...
01-05-2013 04:01 PM
OneMoreTime Actually I would check it and if it were beyond limits then I would cut it at the factory weld points set it square and level and reweld it..Having a frame with a twist is not all that unusual..

Sam
01-05-2013 03:38 PM
jr2009 ok so if it was a bit twisted, would it straighten back out when the body is put back on?
01-05-2013 03:28 PM
OneMoreTime Take a 4 foot carpenters level and lay it across the front and rear frame horns to see if there is twist as well.. those frames are a bit flexi flyers without the body on them so not to worry too much as they can be made straight..

Sam
01-05-2013 02:56 PM
jr2009 Hey thanks for the info!

I'll take that measurement drawing with me, and measure it all out before I buy. so if the frame isn't straight then and of those measurements wouldn't be correct right? give or take 1/4" or so.
01-05-2013 02:03 PM
MARTINSR Here is a place with the specs.

Chevelle Frames

The spot marked is a very common place to have damage from being hit in the front. The frame horn may look undamaged but this area will bend easily.

Brian

01-05-2013 01:08 PM
dinger Brian has made some excellent points. I would look carefully at the frame from the horns (front) to the cross member, look for heated and repaired areas, kinks, rivet replacement, anything that looks out of whack. And like Brian says, 1/4 inch is often what the factory deemed acceptable fo out of square. Moving this to basics, I believe it will get more exposure there, some very helpful info.
01-05-2013 11:56 AM
MARTINSR I don't know the measurements of your frame, but a simple cross measuring will usually tell you an awful lot. Both sides aren't going to be bent exactly the same in an accident, most likely that is. Of course it's possible but usually one is different than the other. Here is a basic cross measuring plan.





Find "control points" that are the same on both sides. The frame is covered with them, very seldom is one side not the same as the other, it will be obvious, just look side to side and if there is a hole in the same spot on both sides chances are they are identical and usable control points.

Those A body frames are very similar all the way from 64-67 among all the makes, Buick, Olds, Pontiac and Chevy, you want to look at the frame ends closely to be sure they are the same as yours. Measure how long they are from control points around the suspension mounting to the over all length. In other words measure from say, the rear shock mount back to the rear of the frames crossmember to be sure it is exactly the same as yours. Do the same at the front. Take some photos of your front and rear frame horns where the bumper brackets bolt, take them with you. This is one area that changes among these frames.

When you do these measurements a little off isn't a big deal and a quarter inch difference is common with these old frames when they were new.

If you can put the frame on a level ground with jack stands under the "torque boxes" that being right at the front of where the fire wall mounts to the rear of the passenger compartment. With the frame sitting like this and you lay a level across the top of the jack stands and it's level you can then put the level across the front and rear of the frame horns and see if those are level to see if the frame is twisted. These are of course pretty basic checks and it would be nice to go crazy with a measurements off the floor and what but you need a REAL nice level floor and you probably won't find one where you get the frame. But if the jack stands are level and you get the frame on top of it at those points the level over the tops of the frame horns is going to do a decent job for you.

Brian
01-05-2013 09:12 AM
jr2009
chevelle frame

Hello everyone,

I have recently discovered my frame on my 67 chevelle is beyond repairable and is also twisted, I have decided to junk it. and get a doner.

I found a guy selling a 66 frame. when I go to pick it up what should I be looking for to make sure I am getting a good straight frame? any crucial measurements to take?

any advice is greatly appreciated.

Thanks
JR

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.