Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> 68 camaro
User Name
Password
lost password?   |   register now

Thread: 68 camaro Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-10-2013 06:26 AM
deadbodyman
Quote:
Originally Posted by cdminter59 View Post
If buying sheetmetal make sure you get Auto Metal Direct. Their sheetmetal fits better than Goodmark or DynaCorn. Also check with Classic Muscle (Classic Muscle.com parts for Chevy performance and restoration ) for other parts. They are located in Winston-Salem N.C.
are you a bodyman ?how many have you done??? I'm always looking for better quality parts
01-09-2013 01:36 PM
cdminter59
68 camaro

If buying sheetmetal make sure you get Auto Metal Direct. Their sheetmetal fits better than Goodmark or DynaCorn. Also check with Classic Muscle (Classic Muscle.com parts for Chevy performance and restoration ) for other parts. They are located in Winston-Salem N.C.
01-09-2013 06:18 AM
496CHEVY3100 Not the npd ,I will be ordering 1 LF fender from npd to replace the Goodmark fende on my car 3/4" to long hood will not align grill will not bolt flush ,smaller parts or cut to fit parts are ok from goodmark but dont like their fenders. mine is a 66 ss 396 ,auto ,air . factiry air cars have different fenders, engine aws replaced in 67 a 427 400 hp.To many cars to little timd.
01-09-2013 05:02 AM
deadbodyman Have you ever tried thier front fendersm 496 ? I have a 68 that needs a complete nose to replace a glass one...Im dreading fitting the fenders..
01-08-2013 07:00 PM
496CHEVY3100 A close freind is a Goodmark dealer so i use some of their parts ,price is rite ,but for most consistant good fit very little prep work National parts depot has the best ive used But prices are higher ,when considering labor cost to repair cheaper parts NPD make sense to me.My opinion
01-05-2013 04:37 PM
deadbodyman I like goodmark for the door skins and 1/4's but I like the full 1/4's and cut them down,they fit so much better than the half 1/4's ,the floor pans are good the rear wheel outer tubs are a little crappy but the inners are good front fenders no good but only tried one and returned it never tried a second..pretty much all good with the exception of the fenders, when they offer two, get the more expensive one you'll be better off...Oh I replaced the rear frame rails too and they were perfect...the cowl hood was the best I ever got only needing a little poly putty around the outer edge and some deburring underneath ,minor hammering at the corners ,all and all a very nice hood.
On the 68 everything is about the same but the firewall and dash were very good also
01-05-2013 08:58 AM
mr4speed I have found that a company called TRIM PARTS has the best quality for what your looking for. Most everything they make is USA made so expect to pay a little more than the average repop stuff goes for. On the sheetmetal Dynacorn is your best bet, and you still may have to trim to fit it properly.
01-04-2013 08:50 PM
carolinacustoms
68 camaro

Please forgive me if I overlooked this in my search and it has already been discussed. I am starting on a 68 Camaro and need to know which company offers the best quality parts? I know theres an NPD about 60 miles or so away and a friend had good luck with there parts on a Chevelle a few years back. I wanted to check and see what suppliers you guys are using and the satisfaction level. I deal with aftermarket/repro parts regularly so I know they have to be "massaged" sometimes to get a good fit, but just wanted to see who seems to be the best quality. Especially for the emblems and trim. Some of it I can have rechromed but the emblems and taillight trim etc are junk. Also probably gonna need a Driver side full quarter and full floor pans from firewall to taillights. As always thanks for all the help.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:03 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.