Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Camshaft Indentification
User Name
Password
lost password?   |   register now

Thread: Camshaft Indentification Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-12-2013 02:10 PM
Hotrod1979 Thank for your help guys! Starting a new thread about cam selection.

Seems a little off topic for this thread.
01-11-2013 12:32 PM
Hotrod1979 Today I removed the camshaft. I came to the conclusion that it would be better to replace it.

The question is, what would be the best cam for this engine?? And what springs would work with this cam and these heads??

It's a 383 stroker engine with Dart iron eagle SS heads. 72CC chambers. 165CC runners, 2.02 intake and 1,96 exhaust.

Compression end pressure is 184 PSI. I think compression ratio would be arround 1:9,5
01-10-2013 02:44 PM
lmsport I'm guessing Lunati Bracket Master 300/300
01-10-2013 09:38 AM
Hotrod1979 I contacted Bullet Racing and this is not their cam...

Tomorrow I will measure the lift on my cam and check the spring height.
01-07-2013 02:16 PM
techinspector1 I'd bet a nickel that Greg T has nailed it, Bullet Racing. According to what I see on their site, this would be a hydraulic flat tappet cam. If it were a roller, it would have a HR designation.

Looking up a Crane cam with close to the same specs as the BR cam, I find the following information for parts to be used with that grind. The first two choices listed will fit into the stock OEM spring seats. The third spring shown here will require seat machining to increase diameter of the seat.

Springs, Crane 96802-16, retainers 99915-16, locks 99097-1
Crane Single Valve Springs 96802-16 - SummitRacing.com
(1.260" spring seat diameter)

Springs, Crane 99846-16, retainers 99944-16, locks 99094-1
Crane Single Valve Springs 99846-16 - SummitRacing.com
(1.255" spring seat diameter)

Springs, Crane 99838-16, retainers 99969-16, locks 99094-1
Crane Double Valve Springs 99838-16 - SummitRacing.com
(1.465" spring seat diameter)
01-07-2013 11:50 AM
Hotrod1979 Haven't found it yet..
01-06-2013 07:59 AM
Greg T
Quote:
Originally Posted by techinspector1 View Post
I'll give it a shot. Don't know who BR is, might be something like B-----Racing. The 300 might be the advertised duration of the cam. Don't know what the -2 is, but pretty sure the H is hydraulic. The 3444 might be the cam lift (0.3444"), which multiplied by the rocker ratio of 1.5 would equal valve lift of 0.5166". 11-18-02 might be the production date.

Could be Bullet Racing, maybe?
01-06-2013 04:33 AM
cobalt327
Quote:
Originally Posted by Hotrod1979 View Post
I checked the number on the back site of the Cam.
The engine is not taken apart..
Might want to see if there's any ID markings under the cam gear.

I agree 300 is the advertised duration.

You can see if it's a solid or hydraulic and if it's a flat tappet or roller (be sure to not mix flat tappet lifters up- the lifter is married to the lobe it was used on). I suspect it's going to be a flat tappet hydraulic, like 99% of the SBC cams being used today.

Measure the valve lift at the pushrod and see if that, along w/the 300 degrees advertised duration, matches up to anything.
01-05-2013 05:55 AM
Hotrod1979 I checked the number on the back site of the Cam.
The engine is not taken apart..
01-04-2013 06:31 PM
hcompton Did you mark the lifters when you took it apart?

Where did you get the engine from most shops keep records of engines they sell. Even if it was a few years back they can probably tell you what kind of cam is in it.

At this point if its out i would probably replace the cam and go on. A bath room scale and a press can tell you abput the springs. Calipers will also be needed. But you should be able to find something that matches up minus a few pounds for age.
01-04-2013 04:26 PM
techinspector1
Quote:
Originally Posted by Hotrod1979 View Post
I have to know what kind of camshaft I got in my 383 stroker to order springs for my heads. Found a number on the back of my camshaft but can't find info on it..
The numbers are:
3444
BR300-2H
11-18-02
Does anybody know what kind of cam this could be??
I'll give it a shot. Don't know who BR is, might be something like B-----Racing. The 300 might be the advertised duration of the cam. Don't know what the -2 is, but pretty sure the H is hydraulic. The 3444 might be the cam lift (0.3444"), which multiplied by the rocker ratio of 1.5 would equal valve lift of 0.5166". 11-18-02 might be the production date.
01-04-2013 03:19 PM
Hotrod1979
Camshaft Indentification

I have to know what kind of camshaft I got in my 383 stroker to order springs for my heads. Found a number on the back of my camshaft but can't find info on it..

The numbers are:

3444
BR300-2H
11-18-02

Does anybody know what kind of cam this could be??

Thanks


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.