Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Home A/C a-coil for a air compressor air dryer?
User Name
Password
lost password?   |   register now

Thread: Home A/C a-coil for a air compressor air dryer? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-07-2013 12:52 PM
66GMC
I've just added this, and a few more pics of this to my project journal.
01-07-2013 11:23 AM
66GMC
Quote:
Originally Posted by kevs79 View Post
Is that 1/2 copper tubing? Are there 4 valves on the wall(1 in each "u" and 1 on each drop at each end?
Yes, you're correct on both counts.

I used (expensive) ball valves like these ones on each of those 4 locations, and came up with a conglomeration of sweat-on fittings (don't trust compression fittings with 125 PSI) with swivels to allow for dissasembly if needed.
I pretty much cleaned out the local plumbing supply ...












A little later on, I found some sweat-on mini valves and used them for the outlet drops. Yes, every outlet has a drop and a ball valve so that moisture can be ejected.

Maybe I'll take some more pics after I clean up my messy garage. LOL
01-06-2013 09:28 PM
kevs79
Quote:
Originally Posted by 66GMC View Post

This is what I made, and it seems to work very well.
Yes it has ball valves on every vertical drop.

Very little moisture ever makes it to the water trap.
Is that 1/2 copper tubing? Are there 4 valves on the wall(1 in each "u" and 1 on each drop at each end?
01-06-2013 10:58 AM
41 kustom
Air

I did one just like yours 66. I can run my blasting cabinate now that I did. It works great at a good cost.
12-31-2012 05:13 PM
66GMC

This is what I made, and it seems to work very well.
Yes it has ball valves on every vertical drop.

Very little moisture ever makes it to the water trap.
12-28-2012 08:45 AM
John long
Quote:
Originally Posted by Old Fool View Post
Make sure you wash it out real good, a/c or transcooler. They both have had oil in them.
How much pressure is a trans cooler designed to handle?

John L
12-28-2012 06:27 AM
BWS Got a new camera,see if this works.One is the "infamous" Franzinator....with external cooling coil(total loss system,IOWs 1/4" tubing taps into water supply but instead of tying back in,it simply fills a bucket.Only use this when AC is runnin non-stop.....and the water is simply adj to dribble).

The other pic is a copper coil.Its 3/4 that was simply coiled around a big sander drum or sumthing?Anyway its gonna be installed after comp.....

I need to tig up another expansion chamber on comp outlet...then plumb the above coil in....just need the time to do it....duh.

Good luck with your system.
12-26-2012 05:10 AM
Old Fool Make sure you wash it out real good, a/c or transcooler. They both have had oil in them.
12-24-2012 07:17 PM
John long
Quote:
Originally Posted by kevs79 View Post
The more I think about it the more i am leaning towards a trans cooler or condensor from a car/truck. The a-coil is so big and takes up alot of room I don't have. I can pick up a trans cooler from the local pick n pull for 10.00 and it would be small enough that it would not take up much room.
I am thinking going up the wall from my compressor to the cooler, then out of the cooler down to a tee w/a leg w/a drain at the end, then back to the tank.
That will work but I think you may get more water than you think. I would be tempted to pick up a 10 gallon air tank and run through it to catch the condensation.

Please let us know how it works out.

John L
12-24-2012 04:26 PM
kevs79 The more I think about it the more i am leaning towards a trans cooler or condensor from a car/truck. The a-coil is so big and takes up alot of room I don't have. I can pick up a trans cooler from the local pick n pull for 10.00 and it would be small enough that it would not take up much room.
I am thinking going up the wall from my compressor to the cooler, then out of the cooler down to a tee w/a leg w/a drain at the end, then back to the tank.
12-23-2012 09:38 AM
John long Of course you are right. I engaged my typing finger before I put my brain in gear. I was thinking of automotive unit. I would think the home evaporator would work great. You would need to have a small tank to catch the water before it got to your compressor tank but that should not be too hard to find either. This is something I have also wanted to do. I hope you will post your progress along with a few pictures as you go. Good luck.

John L
12-23-2012 08:50 AM
kevs79 As far as restrictions go, it looks to be ok. It has a 3/8(I think) small line going in and that splits off into smaller 1/4(I think) lines an goes into the core.
The a-coil is the evaporator portion that is in the house above the furnace fan. The condensor is the part outside and would be way too big to mount anywhere. I have that unit also and was going to scrap it.
12-23-2012 08:43 AM
John long Is the A coil the condenser or the evaporator? I would think the condenser would be more effective though either would be an improvement. You will also need a catch tank for the water that will condense out as the air cools.

John L
12-23-2012 08:29 AM
joe_padavano
Quote:
Originally Posted by kevs79 View Post
I have been reading it is a good idea to cool the air coming from the pump before it goes to the tank and have a water trap after the cooler. Alot of guys have used an automotive evaporator or condenser to cool the air. I have an old a-coil from home unit and was thinking of using it. I was going to plumb it between the pump and tank and have a water trap before it goes into the tank. Also would add a fan to blow into the a-coil just like your furnace does to dissipate the heat. Of course I would have to eliminate the expansion valve on the a-coil to remove that restriction.
Any thoughts?
The only things I can think of are 1) be sure the coil is internally clean and 2) what's the tube size? If it's too small, it could be a restriction to flow rate.
12-22-2012 11:45 PM
kevs79
Home A/C a-coil for a air compressor air dryer?

I have been reading it is a good idea to cool the air coming from the pump before it goes to the tank and have a water trap after the cooler. Alot of guys have used an automotive evaporator or condenser to cool the air. I have an old a-coil from home unit and was thinking of using it. I was going to plumb it between the pump and tank and have a water trap before it goes into the tank. Also would add a fan to blow into the a-coil just like your furnace does to dissipate the heat. Of course I would have to eliminate the expansion valve on the a-coil to remove that restriction.
Any thoughts?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:43 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.