Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Ok you hate the way my Nova front clip is attached
User Name
Password
lost password?   |   register now

Thread: Ok you hate the way my Nova front clip is attached Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-09-2013 07:16 PM
lakeroadster
Quote:
Originally Posted by 4garages View Post
Now I am after an "under bed" gas tank....
What's the width of your frame rails? Check this out, might be of use to ya! Rear Mount Gas Tank 63-72 Short Bed Step Side - Classic Parts Talk
01-09-2013 06:33 AM
4garages
Sounds like I may have options for improving the front clip

Thanks for all the comments and suggestions. I will definately spend some time modifying and re-supporting the front clip attachment on my 40' truck before considering scrapping the old work. Based on many of your comments, with a little extra welding and frame support work I think what I have is worth saving.
The truck sits nice and level and feels correct on the short quiet trips I've taken around the block. It may not be pretty but I think what has been done by the previous owner was well set up, level and sqaure.

Now I am after an "under bed" gas tank and an after market truck bed.
Hope to be on the road and legal by March 1st.
01-08-2013 06:39 PM
1971BB427 If you measure everything out and it is square, then I'd box the connecting point differently. I'm not sure I'm crazy about the two frames sitting alongside each other, although they may be strong enough. The blunt ends are not pretty.
I would cut plates that will make a more gradual transition from the two frames, and add them to what you have. Grind off anything that's sticking up past the frame's outter edge, so when you add the transitions it's smooth. These angled plates will further work as gussets and enforce the area further also, plus make it look more professional.
Just taking what you have now and making all the square ends angle out at 45 degrees and boxed closed, will make it all look better, and be stronger. Do the angles on all edges, leading, top, or wherever there's a difference between the subframe and existing frame.
01-08-2013 03:27 PM
lakeroadster
Quote:
Originally Posted by RWENUTS View Post
The killer question is!!!!
Will it or has it passed inspection wherever you're going to drive it.
Inspections? What The ?? Oh, Yep... a Canadian.

Inspctions, We Don't Need No Stinkin Inspections...
01-08-2013 08:34 AM
RWENUTS The killer question is!!!!
Will it or has it passed inspection wherever you're going to drive it.
01-08-2013 08:22 AM
lakeroadster Based on what I can see in the photo, and what you are describing, I guess I am not getting the "poorly installed by previous owner". Sounds pretty well thought out.

Are the engine mounts on the crossmember or the frame? The reason I ask is the front crossmember stiffens the frame a huge amount, compared to the stock set up. If the mounts are on the crossmember, or close to it, and you have a decent transmission crossmember, I'd think you are good to go as is.
01-08-2013 07:17 AM
4garages
1940 Chevy truck

The front tires do not stick out past the fenders. The hood and fender set up may be wider than stock but the wheels seem to sit just right with good clearance all around.
01-08-2013 07:04 AM
lakeroadster I, for one, don't hate the way it's installed. The clip is wider than the frame, thus the beast is born.

Do the tires stick out of the fenders? (Can't see if the front tires are mounted in the photo)
01-07-2013 11:35 PM
techinspector1 Well it ain't real purty, but is it in there square and workable?
01-07-2013 10:16 PM
4garages
Ok you hate the way my Nova front clip is attached

Other than starting over...how can I improve the attachment of my Nova front clip to a stock 1940 truck frame (poorly installed by previous owner).

Also, other than boxing the frame is there a way to install cross supports to the existing 40' frame and improve the strength. Not building a race car.....just a weekend cruiser.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.