Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> 383 on pump gas
User Name
lost password?   |   register now

Thread: 383 on pump gas Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-16-2013 06:18 AM
Greg T You can do all that if you like and won't change much. I would just install a water injector and call it a day. If the motor is not built yet, change pistons.
01-15-2013 10:09 PM
prostcelica I want to get the compression down. What about getting a little from everywhere. Run a couple thou thinker gasket, polish the chambers and pick up a cc or 2 and enlarge the valve reliefs slightly (I've heard of people doing this. Not sure if its a good idea)
01-15-2013 06:15 PM
prostcelica So will 10.95:1 work well on 94 ?
01-15-2013 12:36 PM
crownver Yes, but will it cost as much power as lowering the compression to use 91?
01-15-2013 12:34 PM
vinniekq2 Try to use chevron 94 as it contains no ethanol. 10% ethanol will cost power
01-15-2013 12:16 PM
crownver Why don't you just plan on using 94? There's at least 1 gas station near you that sells 94 (10% ethanol). Husky/Mohawk in town and possibly the one south of town near your brothers place. There may be others too. Pretty sure 10% ethanol is ok as long as the carb and fuel lines can handle it.
01-15-2013 11:47 AM
Greg T You may want to consider H2O/meth injection. For a few hundred you can run that compression and fuel without worry. I've used these in the past they work VERY well.
01-15-2013 10:22 AM
ssmonty prostcelica,
Even though your post was directed to someone else, I thought I might chime in. I have spent alot of time with a set of RPM heads(70cc advertised) cc'ing, and trying to equalize the chambers. Unfortunately I didn't measure them before I started blending sharp edges around the seat inserts, and polishing to give you an idea how much of a difference it made. I know the polishing is just going to get covered with carbon, but from what I've read it will still help a little to reflect heat back into the chamber and avoid hot spots.
The point I was trying to share is that it takes a lot of grinding to make much of a difference. To gain 5cc equally on all chambers without compromising their integrity would take an extremly long time if even possible IMHO. You would have to remove alot of metal that might weaken them or hurt their combustion efficency, but JMO.
I believe you would be much better off buying another set of pistons with a 12cc "D" dish, but JMO.
I'm in process of building a 383 much like the one you described. 0.040 overbore, 5cc vr pistons, 4.166" x .039" gasket, and zero piston to deck height with 71.4-72.0 cc chambers. I get around 10.2-10.3:1 CR. I trying the groove thing for all the insurance I can get, even though I have no proof they work. Forgive the spelling.
01-15-2013 08:49 AM
prostcelica 10.94:1 is defiantly not idealfor what we want to do with the car .I'd rathher see it between 10-10.5:1 (ie 10.2:1). Fbird, what do you think about opening up the chambers 5cc's or so? If I used the texture from the casting as a guide and sanded evenlly across the chamber how many cc's wold I pick up?

I defianlty want to be able to run on 91 with no issue.
01-14-2013 11:59 PM
prostcelica Thanks Vin. Sounds like a plan. Ill get a head cc'ed in the next day or 2. I aslo called the guy who ground the cam. He said there will be a part # on the back. I'm going to slide it out and get the part number. He said he would be more than happy to provide me with the specs.
01-14-2013 11:47 PM
vinniekq2 after you get a chance to measure the heads,we can get the master tech to do some math.We need the cam specs too.The cam can be put in a couple degrees late if required.Im more concerned the heads were milled. I tune my car for 92 octane and my CR is 10.75
01-14-2013 11:36 PM
prostcelica They are advertised as a 64cc chamber but I've read sometimes they aren't bang on. I think there is a stations that sell 94 octane but I'm not 100% sure. We want to be able to run it on 91. Don't want to have to drive across town to put gas in it. Hey Vin. What do you think abot opening up the chambers a bit?? Or do you think we will be ok on 91. It will be extremely time consuming to grind and cc every chamber I would think.
01-14-2013 11:26 PM
vinniekq2 Man that car is gonna scoot!measure the combustion chambers.what is the best fuel in your area?
01-14-2013 11:05 PM
prostcelica I tried attaching the link for the cam I used to calculate DCR. It is a comp XR288HR. The duration is close so I used the closing point of the intake valve assuming it would be close.....but you know what they say about assumeing. I will be checking all of the timing events with a degree wheel.
01-14-2013 10:48 PM
383 on pump gas

Hey guys

Me and my brother are building a 66 acadian. We just picked up a sbc 383 from a freind of a friend. The guy we bought it from didnt know alot about it so i pulled the heads of to check piston to deck height and do a little clean up on the heads. Im wondering if we are going to be able to run this thing on 91 octane. Im getting 10.95:1 with a dynamic of 8.43:1

SBC 350 40 over
Scat 3.75 crank
speed pro flat tops (5cc)
Felpro head gasket 4.166 bore/.041 comp thick
Piston 5 thou in the hole
Colt custom ground cam 234@50(didnt come with a cam card and I haven't degreed it yet so I used Intake colsing point from this cam
Edelbrock performer RPM heads (64cc)
Air Gap intake
750 double pumper
hooker long tube

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:39 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.