Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> 68 Camaro dash pad recovering help
User Name
Password
lost password?   |   register now

Thread: 68 Camaro dash pad recovering help Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-19-2013 02:24 PM
DanTwoLakes You're welcome. That's why they give me the big money here.
01-19-2013 01:39 PM
JJ269J
Quote:
Originally Posted by DanTwoLakes View Post
My next question is do you really have to sand it at all? I'd use 1/4" for the whole thing if it doesn't matter.
Good point. This is a custom resto mod type build, so I'm not to concerned with factory original look. I just might try the 1/4" and no sanding and see how it looks and go from there. You've been a big help. Thanks.
01-19-2013 01:20 PM
DanTwoLakes As long as the dash is out of the car, any sander will do, but if you have a pneumatic in line sander, and a DA for the finish work, I would think that would work really well. It won't take a lot of grit to sand it down, just do a little trial and error. If you can't find any 1/2" closed cell, I have a supplier that has it. A yard of it 60" wide would be about $30 shipped directly to you. I don't know if I can buy less than a yard, but I'll check. PM me if you want me to get it for you.

My next question is do you really have to sand it at all? I'd use 1/4" for the whole thing if it doesn't matter.
01-19-2013 12:53 PM
JJ269J One more question. I bought some stuff from yourautotrim.com in the past, but they do not have 1/2" closed cell foam. Who do you recommend as an online resource?
01-19-2013 12:44 PM
JJ269J Thanks for the quick reply Dan. I will give that a shot. What would you suggest I use to shape the 1/2" foam? Would a flat sanding board work? I have several and a pneumatic in line sander. What grit sand paper do you use for this type of task? I will take my time with it, but do you suggest any tricks to make sure I maintain a uniform shape? Thanks again.
01-19-2013 10:45 AM
DanTwoLakes I would use 1/2" closed cell foam for the whole thing, and grind it down in the back. Don't put any sew foam over it, just smooth it out to your satisfaction and then glue down the vinyl over the top of the closed cell foam. Closed cell foam is very firm, and it will be easier to keep the vinyl smooth than with softer foam. You need to scuff the surface of the closed cell foam on both sides anyway, or it won't accept the high temp top and trim contact adhesive you should use to hold everything down.
01-19-2013 09:52 AM
JJ269J
68 Camaro dash pad recovering help

Hey guys,

I'm needing some opinions on how to attack restoring the dash pad for a 68 Camaro. The original was heavily cracked and the frame rusted. I removed the foam and cover (mostly in pieces). I wire brushed the frame to remove most of the heavy rust and plan to coat it with Rust Encapsulator before recovering. The front of the dash (leading edge) foam looks to be about 1/2" thick and it tapers down to about 1/8" at the back (see pic #2 below). So my question is, how do I recreate this smoothly? Any other recommendations for covering this? I was thinking maybe just covering the whole thing with 1/4" closed cell foam and covering that or using 1/2" sew foam but I don't know how to taper it smoothly. I was also wanting to add a seam on the top leading edge for a more custom looks with contrasting color thread. Also, because I don't know that its possible to cover the whole thing with a single piece of material. Thanks!










Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:53 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.