|02-09-2013 10:28 AM|
|vinniekq2||the 434 in my corvette is 10 years old.|
|02-09-2013 06:52 AM|
if proper rings/honing procedures are used, oil consumption should be no higher than any other small block of similar configuration (hot street use, drag race, circle track etc.)
not sure which dart block they are using, but there should be no issue using any quality block from dart, world, etc.
|02-08-2013 09:58 PM|
|fast383||Hey guys I have a few concerns about this engine was wondering if you guys could help me out. First of all I was concerned about the 4 inch stroke this engine I've heard that it can be problematic it's not the best set up. I have also heard horror stories about 427 small block oil pan fitment something like you can only use every other bolts because of clearance issue is there any issue with this? Also I'm concerned with oil consumption with the 427 small block? Also are there any issues with running one of these darts locks on the street|
|01-28-2013 08:19 PM|
|vinniekq2||A 427 could spit out that muncie with no troubles at all.You should beef up the muncie|
|01-28-2013 08:14 PM|
|fast383||Would these 427 small blocks be able to live in front of an m21 Muncie 4 speed? Freshly rebuilt?|
|01-23-2013 07:23 PM|
I used cnc many times they are also much more likely to over speed the bit and trash the work peice and continue to do so until your block and bit are both scrap metal.
The price is right and the motor is the right stuff. Dart tall deck block with pro 1 heads should be in the 500 hp range woth good cam and compression.
Now make that an 18 degree motor and the same 427 is 700 hp and 20k.
If 550 hp is more than you need you should be happy if it lives up to spec. But if you think adding a fogger plate later on is a good plan better think about another rotating assembly for any upgrades. Consider it maxed out and you will be happy.
|01-23-2013 05:37 PM|
|01-23-2013 05:19 PM|
i get so tired of hearing "cnc" as a buzzword that most don't even know what they do. yes they have a place in machining, but they are not the do all, end all, piece of equipment that some would have you believe.
I've always said a crap machinist can make junk on the nicest cnc, but a great machinist can make outstanding stuff even on worn out junk. it truly comes down to the person running the stuff.
|01-23-2013 05:13 PM|
A machinist can also make a mistake with a C N C machine.
C N C machines dont slip as often as people,they usually follow the program
|01-23-2013 04:51 PM|
a cnc machine does not know casting thicknesses so what difference does that make?
i recently did one, not on a cnc and also not hand ground. i do block clearancing all the time on a simple manual mill.
|01-23-2013 03:51 PM|
so tri star engines 427 sbc (560 hp) $6,800 shipped.
shafiroff 427 sbc (525hp) $10,000 just over 10k shipped.
i have a hard time justifying buying shafiroff, it seems their prices are very very high.
|01-23-2013 10:44 AM|
2618 Forged Pistons
4340 Forged H-Beam Rods.
What I don't see is who makes them. Big difference in a part that's been fully inspected/backed by a reputable company and a generic imported part that carries an unknown or "off" brand. Not that Scat isn't imported (don't know if the raw castings/forgings are sent here for machining, or what), but they seem to do a better job than some of inspection and/or specifying/applying the spec tolerances.
|01-23-2013 10:38 AM|
|01-23-2013 08:30 AM|
i just received the info from them. The crank and rods are SCAT.
The pistons are forged (KB - Icon)
Icon Forged Racing Pistons
|01-23-2013 08:08 AM|
|vinniekq2||another thing to consider(worry about) not all machine shops can machine a 427/434.They might try to talk you into a 420.The block should be C N C machined for clearance,not ground|
|This thread has more than 15 replies. Click here to review the whole thread.|