Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> How to ID what year a 700R4 transmission is?
User Name
Password
lost password?   |   register now

Thread: How to ID what year a 700R4 transmission is? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-27-2013 03:35 PM
mmerlinn That is an 87, so you have what you are looking for.
01-26-2013 10:54 PM
Bobkat OK, suggested that I find the number on the pan rail. here is what I found. 7TXM085A
Now I am told that my 84 was a bad year and 87 was what I need, is this correct? It is going in an 84 c20
01-26-2013 08:10 PM
mmerlinn The unknown 'shaft' in the front is the stator support for the stator inside of the converter.
01-26-2013 06:33 PM
Bobkat yes, I made a big error in my last post. Input shaft is at the front. It has a smaller longer shaft with 30 splines. There is an outter shorter larger od shaft which the smaller longer shaft comes through (center) which I do not know what it is for. It has 27 splines. Both are at the front (input) of the transmission. I looked for a tag on top but unfortunatley the only thing left is adhesive with nothing legible. The person who has the transmission told me that it came out of a 1987 chevy PU but that doesn't mean much as any number of transmissions could have seen service in the truck. So without any diffenitive way to I.D. the transmission then I should pass and wait for one that I am certain is a 1987.
01-24-2013 11:25 PM
mmerlinn
Quote:
Originally Posted by Bobkat View Post
being that I am a novice at automatics I counted the splines on the output shaft. The longer of the two shafts on the front. 30 splines on the long shaft. The shorter shaft has 27 splines. The longer shaft must be the output shaft.
The output shaft is at the opposite end of the transmission from the input shaft. All 700s have output shaft with 27 splines, same as 350s, 4L60s, some 400s, and a few other automatics.

Input shaft counts are all over the board with 700s having either 27 or 30 splines. Just counting the input splines is not enough as some 700s had 27 splines from beginning to end of production. The only 700s that did not have 27 splines were the V8s (and the 6 cylinders using a V8 case) from mid-84 to end of production. All others always had 27 splines.
01-24-2013 12:42 PM
Bobkat
splines

being that I am a novice at automatics I counted the splines on the output shaft. The longer of the two shafts on the front. 30 splines on the long shaft. The shorter shaft has 27 splines. The longer shaft must be the output shaft.
01-22-2013 11:51 PM
mmerlinn None of those numbers mean anything for identification purposes as all of them are casting numbers, some of which (like MD8) apply to all 700 transmissions. The only numbers that would matter would be those applied AFTER the transmission was built in the factory. All of the numbers you give would have been applied before final assembly, sometimes months or years before.

There should be a paper or plastic laminated tag glued to the top of the bell housing. Some of the numbers on it would tell the year. Production codes stamped into the pan rail will also tell us. Numbers stamped anywhere else are meaningless for this purpose.
01-22-2013 10:48 PM
Bobkat This is all I see for ID on this transmission unless I missed something.

1. The number "3" on the right side above the TV cable location
2. The letter "K" on the right side of the bellhousing area
3. "MD8" on the right side bellhousing about 5" below the letter "K"
4. The same letter "K" on the left side bellhousing
5. The same number "3" on the left side of the tranny
6. The plate inside the bellhousing that holds the seal for the torque converter has "8654303" on it.
01-22-2013 12:39 AM
mmerlinn Tag numbers will tell you the year. So will the production codes on the pan rail.
01-21-2013 08:00 PM
scholman count the splines on the input shaft.....weak trans has 27 splines
stronger has 30 splines. Corvette and IROC transmissions also have better oiling so if you rebuild the 30 spline 700r4 put in the better internal parts for a very strong trans.

Scholman
01-21-2013 07:26 PM
Bobkat
How to ID what year a 700R4 transmission is?

How can I tell what year a 700R4 transmission is. I have an 84 and it has gone to crap twice on me. I am told that I need an 87 as the early ones were problematic. So once again how do I tell that it is an 87, serial numbers or what?

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:06 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.