|02-06-2013 10:11 PM|
So I first straightened the hinge arms. This would have brought out the gas door and back a tad. You can see where one arm was bent so bad it cracked paint.
Then I dealt with this side of the hinge to push the pivot point tight against the skin and forward. So after straightening the first hinge it would have brought the gas door to far out, but after moving the pivot point forward and closer to the skin it brought it back in and more level with the surface around the gas door opening, thus undoing the prior damage to the hinges on the gas door
Also had to plug weld to out skin due to broken welds, which also contributed to the gas door hitting.
time to get this done! I could have cut slices on the quarter but would rather fix what's wrong than what's right.
|01-28-2013 07:50 PM|
|tech69||yep. After examining it closely with my new set of eyes, thanks to all the tips you guys gave me, I can see that the rubber stop thing will work.|
|01-28-2013 07:29 PM|
|sedanbob||I like the rubber bumper idea - I have seen several gas doors with a small rubber bumper on the backside of the hinge arm, so that the rubber hits before the lid hits the fender.|
|01-28-2013 05:49 AM|
|deadbodyman||Chip who ????|
|01-27-2013 10:42 PM|
I'm such an accomplished metal shaper now I'm taking my gas door to Chip Foose and demanding a job!
I think I got a bunch of ideas to at least visualize when it's back in front of me. I'll come up with something to "fab" up.
|01-27-2013 06:22 AM|
Well tec, Its all over now ,and theres no going back....You are now a metal shaper...Figuring this kind of stuff out is one of the reasons its so addicting ....Just one problem....when you said "bend" the hinge...Your new term should be "reshape" the hinge....Bending sounds so.....cavemanish
Judging by the pic it looks like the door is a little to far forward and the gao is a little tight so Imagine your sticking a screwdriver in the gap and twisting it so the gap opens up....which way is the hinge going to bend ...the rest is up to you....
|01-26-2013 05:11 PM|
|496CHEVY3100||If i understand correctly sounds like you could use a small rubber bumper like the ones inside glove box on older chevys ,just drill a 1/8 hole in hinge and pull the rat tail thru hole leaving the cone shaped rubber to adjust height trim rubber to fit. Good luck..|
|01-26-2013 01:58 PM|
|RLDSL||The shape of that door is super unique,and it looks like the geometry just might work.... have you thought of trying a short length hinge set on the diagonal in the bottom right corner, to where it would pull out to the right and down ( small hinge with hoops )? that would look insanely cool ? of course a large one with hoops in the orientation you are in would solve teh hitting problem as it would lift the door out and away. Very easy to make with a chunk of sheet metal and some heavy wire.|
|01-26-2013 01:03 PM|
Sounds like a stop off the hinge going back for the door to hit would do the job, as long as it's opening enough to get the new modern clumsy crap nozzle we have to use here in sunny California.
|01-26-2013 12:39 PM|
|tech69||it just opens too far. Yeah it does hit at the bottom recessed area/jamb of the opening but I think that's cause it's opening too much and when it hits the recessed area it's at the end of it's travel, right before the door completely rests on the opening edge. (The middle of the door rests right on the edge of the opening). It's pretty much what's stopping it. I'll take some pics of the inside of the door on Monday and work around it so I can get more opinions from you and others.I'll take a pic of it opened too.|
|01-26-2013 10:11 AM|
Your hammer forming looks great by the way.
|01-26-2013 10:09 AM|
I don't understand where it is hitting, you mean down in the bottom of the hole when it opens the leading edge of the door is hitting in the bottom of the recessed area of the quarter? If that is the case you need to move the pivot point nearer the edge so it swings out more like a gate, if the hinge pivot point is back away from the edge the front swings in like a door the car swing in the front edge. So moving the pivot point forward is what it sounds like you need.
And that pivot point needs to be as close to the skin of the lid as possible. The further away from the skin the more the lid will move forward before going in at the front needing a wider gap.
Is that where you are, am I understanding this?
|01-26-2013 09:13 AM|
|01-26-2013 09:06 AM|
If ya overlap it, it's gonna throw off the height or depth depending which side you overlap top or bottom
If that makes sense.
|01-26-2013 08:53 AM|
|tech69||I think I might try your idea of shortening the hinge, but first I'm gonna take it back off to check the amount of travel. I can always adjust it and spoon it around after if it doesn't fit the best after doing that. the main issue is the back hitting. will probably cut it and just overlap it with two tacks to mock it up and while on the car, then take it off, scribe, cut and final weld. Not so intimidating once I thought about it for a sec. Thanks for the response.|
|This thread has more than 15 replies. Click here to review the whole thread.|