Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> motor locked after installing c4 trans
User Name
lost password?   |   register now

Thread: motor locked after installing c4 trans Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-04-2013 08:32 PM
tokaanu hi there i checked bell 4 cracks ,none, input shaft comes out smoothly, checked converter snout and there is a slight kinck, i put cv to case and she landed sweet and spun freely i also put cv on donor pump and it landed sweet on that case too. gana take to machanic see if they can do swap, as im not to familier on how to do swap,got that dam pump off the donor at last. if theres any thing im missing let me know,cheers for help much aprciated.
02-04-2013 01:30 AM
tokaanu hi there iv dropped trans today, and il ispect all that youve mention, i have my other c4 which ive started to take apart just so ive got some idea how to remove pump safely ive removed bell,pan,vaules,bolts, but pump hard to get out, any sugestions. mate how can i tell if my pump on other trans is ok cheers.
02-03-2013 01:41 AM
Originally Posted by rick 427 View Post
I don't know what year trans you got....65-69 pumps will interchange.Then 70-77.Then 78-81,followed by 82-86.
65 and 66 pumps used an o-ring seal. All later versions used a gasket seal. Using the wrong type can result in leaks.

70 to 81 all directly interchange. Only difference is sealing ring width.


OP. No specialist tools needed. It is possible, though unlikely, that your pump is ok. Check it out before you replace it.

Also check the converter snout. Sometimes it can get damaged in situations like this. Check your bell for cracks, especially around your motor bolts.

If your input shaft does not slip out easily, you could have damaged your forward drum.
02-01-2013 02:01 PM
tokaanu hi there my stock trans c4 was 71 an c4 that i put in wrong is a 77or78 so i may be able to swap? ganna drop tans today.then see how to go about changing pumps.wandering if any specialist tools will be needed.cheers
02-01-2013 07:56 AM
rick 427 I don't know what year trans you got....65-69 pumps will interchange.Then 70-77.Then 78-81,followed by 82-86.
01-31-2013 07:39 PM
tokaanu thanks guys should of joined hot rodders years ago when i put trans in ,i did it the wrong way fex plate to motor then tc to flex then bell trans to tc ,bugga just wandering i still have my old c4 trans is it possible to swap pumps? any suggestions will be much appreciated,cheers.
01-31-2013 06:09 PM
Crosley Can not rotate converter on C4 application, although there should be movement as mentioned. Converter studs protrude thru the flexplate during install.

Is it possible the converter was bolted to the flexplate first , then the trans installed on to the engine? If so... broken pump is the result.

As it sit now, sounds like a broken pump may have happened
01-31-2013 04:18 PM
motor locked up

sounds as though front pump and torque converter are not aligned.unbolt torque converter from flex plate and see if you can move converter toward transmission,also try to rotate engine. could have damaged front pump if they werent aligned.
01-31-2013 04:05 PM
motor locked after installing c4 trans

hi guys ive just installed a c4 trans to 351clevo tryed to start but no crank no start chacked connections looked ok ,took out plugs tryed to turn by hand woodnt budge, wandering ifin i can get some good advise as im no mechanic ,any help much aprciated cheers.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 03:15 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.