Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Old Compressor
User Name
Password
lost password?   |   register now

Thread: Old Compressor Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-01-2013 06:16 PM
Mac88
Re

Im not sure how much rust is inside, but I may look into having it tested just to be on the safe side.
02-01-2013 04:07 PM
oldred Just place the flywheel back on the shaft and tighten the retaining nut, it does not need to be pressed back on and the nut should easily get it tight enough. DON'T hammer on it! Hammering the flywheel on is not necessary and could very easily ruin the crankcase because the crank has very little in the way of thrust bearings, it does not take much end thrust or hammering to cause serious damage.

Quote:
Originally Posted by Mac88
Has anyone ever heard of putting POR-15 inside a compressor tank to clean out rust and coat the side?
I had a discussion about this very idea recently with a guy who wanted to treat the inside of his tank with a POR 15 gas tank kit and although I have never tried it I think it should help, I doubt it could hurt anything except your wallet. My concern if it were my tank is how much rust is in there? If that thing has heavy rusting inside you really should pressure test it (hydro, NOT air pressure!) before using it, a rusty tank can be deadly.
02-01-2013 03:16 PM
Mac88
Re

Thanks for the reply, got it off, and now two other questions:

1) Any suggestions on how to put it back on? Since I used a puller to pull it off, I dont really see a way to attach to anything to push it back on.

2) Has anyone ever heard of putting POR-15 inside a compressor tank to clean out rust and coat the side?
01-30-2013 02:45 PM
oldred That flywheel does indeed just pull off but unfortunately it's going to TIGHT!!!!! That thing is mounted on a tapered shaft and if you can apply some heat to flywheel hub it will come off a lot easier, just be warned that when it does come loose it will in all likelihood jump off all at once so be ready for that to happen.

Also it's quite likely that the retaining nut will be a left-hand thread.
01-29-2013 07:12 PM
Mac88
Re

Still not finding anything. Does the flywheel just pull off with a regular pulley? I want to take the compressor and engine of the tank and give everything a good cleaning. It looks like the flywheel should just come off with a standard puller. I've already removed the center bolt, which was'nt very tight to begin with.
01-29-2013 06:37 PM
Mac88
Re

Thanks, I will give that a try.
01-29-2013 06:32 PM
matt167 919 is the manufacture code for DeVilbiss which has made Craftsmen Compressors for a long time. You can probably cross the pump numbers with Devilbiss and get some info from them. They are not bad compressors, especially if it's older
01-29-2013 06:05 PM
Mac88
Old Compressor

Today, I came across a Craftsman Air compressor Model Number 919.176840. It's an Oil Lubricated Single Stage Air compressor. I've tried looking on line trying to find more information about the compressor. The only thing I can find is a general owner's manual from sears for Single Stage Compressors. You can tell the compressor has sat for a while, but the guy I bought it from "said he started it up about a month ago and it ran fine. The questions I have is has anyone ever dealt with this compressor and is it any good? I don't want to put money into getting it all clean and serviced up if it won't be worth it.
Also, I'm pretty sure the flywheel comes off with a pulley, but I'm trying to find a manual that shows how to completely disassemble and reassemble this thing. I want to make sure it's sound before I start my next project.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.