Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Painting over rust conversion coatings
User Name
Password
lost password?   |   register now

Thread: Painting over rust conversion coatings Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-09-2013 07:45 AM
Alpha67
Quote:
Originally Posted by mitmaks View Post
Thanks for pointing this out. I do follow directions and I had good experience with POR15. Why? Cause I followed directions and used it over rusted metal and it has held up fine for 10+ years now. There's a few people including on here who blame the product but when you ask them if they used it over rusty metal they will answer "no, do I have to?"
Actually, I followed the instructions to a T. I used DOM16 which is supposed to be equal to POR15. After the coating failed, my complaint to a company official netted me a response that he felt this product was misrepresented by its label which claimed the product could be used on clean, bare metal and previously painted surfaces. He admitted that this product was developed specifically for use on rusty or sandblasted surfaces.
02-08-2013 01:38 PM
mitmaks
Quote:
Originally Posted by Alpha67 View Post
I strongly suggest testing your POR adhesion before you do anything if you painted it on anything that wasn't rusty, rough or sandblasted. I had a massive failure with a comparable product where it blew off in sheets when I hit an exposed an edge with compressed air. I'll never use that stuff on anything other than rusty or sandblasted. Think of POR as "Paint Over Rust"
Thanks for pointing this out. I do follow directions and I had good experience with POR15. Why? Cause I followed directions and used it over rusted metal and it has held up fine for 10+ years now. There's a few people including on here who blame the product but when you ask them if they used it over rusty metal they will answer "no, do I have to?"
02-08-2013 05:52 AM
Alpha67 I strongly suggest testing your POR adhesion before you do anything if you painted it on anything that wasn't rusty, rough or sandblasted. I had a massive failure with a comparable product where it blew off in sheets when I hit an exposed an edge with compressed air. I'll never use that stuff on anything other than rusty or sandblasted. Think of POR as "Paint Over Rust"
02-03-2013 08:24 AM
deadbodyman I used to use rust mort but I found Ospho works much better..You have to be very careful when using acid products...Theres a whole proceedure I use but all I know is how to prep using Ospho...first off you want to remove the rust not just convert it,thats tuff enough...I always sand everything completely with 180 to get off any excess build up from not wiping enough off when done...after that I scuff with a red pad then clean with W&G then I get out the tack rag and give it a good final cleaning...I always use epoxy primer ,I prefer SPI epoxy for high quality and low price...
If you want to know more about how to use Ospho for removing rust, start to finish I'd be glad to help but just remember be very cautious using acid and be very throuogh with your prep because they are the #1 cause for paint failure, usually bubbles...so do your homework and know what to do before you start and you wont have any trouble later on...
02-01-2013 08:23 PM
milo I use Sem's Rustmort there are 2 kinds one needs to be coated (69508) the other can just be left uncoated. . let dry a day or so then sand with 180 and prime with your choice..
02-01-2013 07:36 PM
Lizer I scuff with red scotch brite until there is no gloss left, and then epoxy.
02-01-2013 05:14 PM
mr4speed I shot a set of inner wheel wells for a pick up a while back that were done in por 15. Just a red scotch brite, give it some bite with that then some black epoxy then some satin black s/s. This was just to give it more rust protection, not really high end work. To be honest not too crazy about the por 15.
02-01-2013 01:45 PM
mitmaks
Painting over rust conversion coatings

Does anyone use Rust Mort, POR15, etc. and how did you paint over it. Epoxy primer and then paint?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.