Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Holley carb questions.
User Name
Password
lost password?   |   register now

Thread: Holley carb questions. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-06-2013 11:29 AM
lg1969 Try to adjust the float at lower level. Heat shield is not bad idea.
02-05-2013 05:37 PM
damanx I have a fuel pressure regulator and it's set at 4.5 psi.

Sitting on level ground, I started the engine and warmed it up to do some other things.

After shutting it off and checking it a little bit later, I see the booster in the secondary has some residual fuel around it, but also see fuel around the top of the vent. Not much, but it's there.

The primary bores have a lot as well as fuel around the front vent also.

I am confused.

Edited to add:

It just dawned on me that I have a nice digital infrared thermometer and then checked the temp of the float bowls.

Front was about 112 and the rear was at 118 give or take a few degrees. The engine has been off with the hood open for at least 20 minutes, so that kind of tells me that I probably have a percolating issue and need an insulator.
02-05-2013 09:06 AM
lg1969 Holley 390 only require no more then 4.5 psi of fuel. Go above it and the float valve will be forced open. you may have to replace the needle/seat assy. that can handle higher Fuel pressure. I'm using two Holley 390's on my Tunnel ram setup.
02-05-2013 08:44 AM
damanx
Holley carb questions.

The carb in question is a Holley 8007 390cfm. I got this used and outside of missing the electric choke, which I replaced with the manual conversion, it appears as if it were used for a very short time. I've rebuilt it using the Holley kit.

Now the questions:

1st question: How critical is the leveling a Holley carb? The my Holley is slightly higher in the front than the rear and even though I have the rear float bowl float set slightly lower than the front, it seems to still drip ever so lightly from the booster on the side of the needle.

2nd question: Do inclines affect the fuel levels in the bowls as you are driving up or down them? My driveway isn't real steep, but does have a 20 degree incline proceeded by a ramped curb. Would this be why I see the fuel in the secondary?

3rd question: How sensitive to heat from the engine are the float bowls? I've read a couple posts about heat shields. I've got material that I can fabricate a shield if that would help with the 1st question.

Thanks for the help.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.