|06-23-2013 06:48 AM|
|ap72||Definitely need to lean it up some and may need to look at the timing.|
|06-22-2013 11:59 PM|
|vinniekq2||4000 pounds puts you 300-320 HP|
|06-22-2013 11:42 AM|
|1971chev||3.08 gears a not so good converter and 4,050 lbs with me in it.|
|06-22-2013 09:46 AM|
what was the 60' time? 2.2 ish? does the fuel delivery system have enough volume? should run a high 13 with 96 mph.Its no where near a 12 second car,though we have a few Malibu's that run 12.1s at 102-104 mph.Those cars really launch though.
what gear ratio and converter are you using? You want to "drag" race,you need the drive train to match.
if your car weighs 3300-3400 hundred pounds with you in it,the hp is around 250-275 at the wheels
|06-22-2013 08:11 AM|
|1971chev||Got the truck to the track last night ran a 14.5 at 96 mph|
|06-05-2013 03:20 PM|
|1971chev||I have the 6BTM hooked up just wondering if there is any way to tell if it is pulling timing as it should and also on my vaccum advance should this be hooked to manifold or the carb?|
|06-04-2013 12:12 PM|
|1971chev||Im not sure what that lean spot in the beginning is from but is it safe to say I can drop down a couple jet sizes on the secondaries|
|06-01-2013 01:36 PM|
Here is a copy of the dyno run
|05-29-2013 03:00 PM|
|1971chev||I am just waiting for my dyno graph should have it by tonight or early tomorrow. I have been checking on some things on the truck and just now noticed how close my air cleaner lid is to the top of my carb. There is only about 1/8 inch of clearance could this be causing a major problem?|
|05-25-2013 10:14 PM|
|1971chev||No powervalve, the number on the carb is a 750 main body|
|05-25-2013 09:34 PM|
64cc isn't a bad choice if you plan on running race fuel or ethanol. Maybe you are?
The cam isn't small for street power, it'll definitely limit your peak but with good heads headers and a blower 500hp should still be attainable.
If you're running ethanol I think you may have a pretty strong street runner. Are you running ethanol? If not I'd switch to it.
|05-25-2013 06:51 PM|
Off the bat unless you're running really high boost your timing is probably a hair too low, but you'll probably need better fuel if you put it where it should be.
Jets seem really big to me but I may be wrong, it's been a while since I messed with a Holley.
|05-25-2013 06:39 PM|
|1971chev||Front jets are 81 and rears are 97, timing is 12 initial and 32 all in at 2500.,,ill have the dyno graph on Tuesday blower ratio is 1.72|
|05-25-2013 05:45 PM|
old cam 244º@ .050 int/ex .501 lift,,106ICL 110 lsa
new cam 214/224 @.050" .444/.466 lift,,112 LSA
OP, F' bird gave you some good advice there with the cam, head swap, header size and explained clearly the reasons for them all. You went out got the wrong cam, wrong cc heads and wrong headers???
Your DCR is going to be up even more now that little cam, limiting the amount of boost ya can utilise with pump gas???
Why you ask advice , get advice from one of the sharpest tuners on the forum, and then ???. ..
|05-25-2013 03:56 PM|
|ap72||Post a pic of the dyno curve and tune. What's your timing set at? Af ratio? The cam is fine with 1.6 rockers.|
|This thread has more than 15 replies. Click here to review the whole thread.|