Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Intake Question For Vortec Swap And Future 383 Build
User Name
Password
lost password?   |   register now

Thread: Intake Question For Vortec Swap And Future 383 Build Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-09-2013 01:58 PM
F-BIRD'88 Let me help you with a little towing power ///efficiency math and basic economics.

You can only tow so fast. If you exceed the posted speed limit your luck will run out sooner rather than latter and will not et where you are going any faster.

you need x horspower to climb a hill while pulling a load at the posted speed limit.
let x be EG: 150hp...
Your stock engine creates well in excess of the required 150hp to get up teh steepest hill ( it creates 250hp)
reguardless of how or how much you hot rod the engine it still requires you create 150hp to get up the hill.
and you already have well in excess of the required engine power.

you can still only climb the hill at the practical speed limit. or it will cost you more money to get there.
A LOT MORE IF YOU GET A TICKET doing it.

creating X amount of horsepower requires burning a fixed amount of fuel. reguardless of the engine design.
All you will achieve is burning more fuel to get there You will not get there better or faster.

You only need enough max horsepower to get up the steepest hill with the load at a practical speed.
any more is not better. TOWING IS NOT THE SAME AS RACING.
Going faster while towing is not better and having more horsepower is not like having more money or more food or a bigger noodle.

you will not get there any faster or better or save fuel by hot rodding the enigne in your truck. And the girls will not like you any better. But you will be poorer as a result.
02-09-2013 01:31 PM
vinniekq2 rpm requirements are more air at higher RPMs, a bigger engine needs more air and even more air at high RPMs? how much power do you need,from what size engine?Its just math,,,, bigger engine can supply the greater power,,,sooner

what do you need?what are you hauling,,,,?maybe you need a turbo diesel?
02-09-2013 12:56 PM
Hoyt71 My main question, more or less, is if the Performer RPM is a bad choice for a stock 350 with vortec heads at my vehicles weight and cruise rpm and would it lend itself to future upgrades or will a plain jane performer or similar design do just as well for less money. If its a toss up, then fine. Was afraid the extended rpm range might be a little too high but the dyno sheets from Edelbrock don't indicate that quite so much. Nothing wrong with looking for real world experience. I'm doing the vortec upgrade and need an intake. Things may change before I go bigger.
02-09-2013 12:17 PM
vinniekq2 decide what you need,buy parts for that,towing will require(you fill in the blanks) build that once.Budget is not a word to use,decide what you need and buy the best parts to do that
02-09-2013 11:13 AM
Hoyt71 I beg to differ, but that's OK.
02-09-2013 11:09 AM
F-BIRD'88 Increasing the power of this heavy work truck will not make your life any better.

daily driver/towing more engine power will not get you there any sooner or any better.

but it will cost more.

Just leave the hood shut and drive it. You will get there.
02-09-2013 08:23 AM
Hoyt71
Intake Question For Vortec Swap And Future 383 Build

OK. This is the same 78 350 in a 5200# truck with 3.73 gears and 4 speed manual. Because of the tall tires my cruise is 2000-2200 rpm.

My end use will be a daily driver/tow/haul. I am on an extremely tight budget. My end result I think will be when I rebuild the engine and step up to a 383 build.

For now I am going to freshen up a set of used Vortecs and maybe a cam change.

I have been looking and reading about intakes and have a couple of questions. I want to be able to reuse the intake on a 383 but don't want to kill my 350. It looks like I need to stay away from the air gap type manifolds. Would something like the Performer RPM or similar manifold work well or is there a better choice? I didn't know if the runner size would kill my torque. I am not particular on brands. Is there much difference in tq/hp between the different dual plane manifolds? I am also looking at used parts for cost savings.

On a side note, will my Vortec heads be suitable for a 383 build or would I be much better suited with an aftermarket set? If aftermarket would be better, how much better on tq/hp would they be? This might dictate how much time and money I sink into a set of used heads. Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:55 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.