Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> 305
User Name
Password
lost password?   |   register now

Thread: 305 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-15-2013 12:02 PM
Wezz Haha i know but its for an friend of mine he has a 383 i pud a treath in category transmission
02-15-2013 11:53 AM
painted jester Your stock convertor is fine for your build!

Jester
02-15-2013 11:39 AM
Wezz Ok we stay holding contact haha . Do you knoe anythibg about a lock up conveter?
02-15-2013 11:36 AM
painted jester
Quote:
Originally Posted by Wezz View Post
Ooo im so happy with this treat jester . Nobody can tel me or it was good or bad. You r i verry good man i will get the lost wirewheel wire out . With air. Vacuum cleaner and a magnet butt the marzipan still not arived??? If its coming not to your house i will pay you with paypall if it comes i will suprise you
Hasn't come yet LOL! but I'm in No mans land!!! Very rural area so mail here is slow LOL!

Jester
02-15-2013 11:24 AM
Wezz Ooo im so happy with this treat jester . Nobody can tel me or it was good or bad. You r i verry good man i will get the lost wirewheel wire out . With air. Vacuum cleaner and a magnet butt the marzipan still not arived??? If its coming not to your house i will pay you with paypall if it comes i will suprise you
02-15-2013 11:19 AM
painted jester
Quote:
Originally Posted by Wezz View Post
I mean . I convirted 0.05 mm to inch and came out 0.00196850393701 inch
No! .002" isn't too much!

Jester

Cylinders are probably good if you can see hone scratches! If it ran good before you pulled it, it will probably be fine! just assemble it! and break the cam & lifters in! The only thing I wondered was if steel bristles got into the ring lands from the wire wheel you used to clean the pistons while they were still in the bore!
02-15-2013 02:10 AM
Wezz I mean . I convirted 0.05 mm to inch and came out 0.00196850393701 inch
02-15-2013 01:52 AM
Wezz I convirted 0.500 mm to inch and came out 0.0196850393701 " is that much?
02-15-2013 12:58 AM
Wezz How much tolorance. Can it have btw?
02-15-2013 12:57 AM
Wezz Hi i did that . It was a few hondrerds to large @ some places . I let the pistons in and finish the block . Overbore is more expensive as a 350 block ! and my compression was good If you look good you can see a little hone schratches . So so bad it isnt right!?
02-15-2013 12:48 AM
painted jester Wezz: We aren't used to working in MM convert your readings to inches and post the paper with your readings. Get a pencil and paper write down the measurements of each cylinder tightest to largest dimensions from bottom of piston travel to top you will have several readings for each cylinder! Measure your pistons and see how much wall clearance you will have at the tightest position of travel! I think you measurements are off? By my calculations. remeasure them again!
Or your tool needs to be calibrated! Take your tool to your machine shop and have him check it against his! Is your small dial working It seems to be stuck on the .002mm LOL

Jester
Check your bore gauge with a mike like in this video.




Stock Bore is: 3.736 in or 94.8944 mm

305
Production: 19762000
Displacement: 305 cu in (5.0 L)
Power: 130 hp (97 kW)-250 hp (186 kW)
Bore and Stroke: 3.736 in 3.48 in (94.9 mm 88.4 mm)

MOTOR SIZE....... BORE........ STROKE
V8 - 305........... 3.736........ 3.48
02-14-2013 10:22 PM
Wezz Ok. Hope the marzipan is ariving soon . But how do the cylinderwall look .. Goog enough or bad
02-14-2013 05:17 PM
painted jester The cams are pretty close and operat at the same RPM range!

No Mail yet LOL

Jester
02-14-2013 04:15 PM
Wezz Btw did you see the mail man? Got the marzipan ?
02-14-2013 03:56 PM
Wezz He said he never. Did onley hone . He sayd its better to bore it and then hone .. He didnt see the engine of mine he onley tells me wjat he usually does. But uh i m let the pistons in i. Clean it up with air pistol and an. Vacuum cleaner . But do you see the pics jester!? Do my cyl walls look bad? Btw what is the difference between a 2102 cam and the one who ive got ( the 3702)
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.