Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 406sbc new cam 306s coil bind questons
User Name
Password
lost password?   |   register now

Thread: 406sbc new cam 306s coil bind questons Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-11-2013 07:58 PM
matt921 I don't have any of the warranty stuff from the cam. I bought it from a craigslist seller. Its brand new but he didn't give me any of the paper work in the box. Like I said in the start I have new lifters the cam is brand new im not in a hurry at all to put this cam in as it is still winter and the season here does not start till april. But I will look into different springs.
02-11-2013 07:41 PM
S10 Racer I'm not 100% sure but I thought for the cam warranty to be good, you had to install the correct springs and new lifters for the cam. Regardless, having a good valvetrain is one of the most important aspects of the engine and the most likely to break and cause other engine destruction. I would step back and get the correct springs, get them installed at the right height with good retainers, at least chrome moly and good pushrods not to mention new lifters. JMHO
02-11-2013 07:20 PM
matt921 Yes there are quite a few in the area. I use to work at one of them. I was told by my boss that I could get away with using the z28 springs. That with the lash at what the cam recommends I could use them. But to check for coil bind. The thing is I already have them don't have the cash to go out n spend 200 dollars to buy comp springs right now. What he told me same with the machine shop is I can get away with these springs I have but if I run into issues I can buy retainers that are cupped to help get away from coil bind. but I wanna get a few words on this.
02-10-2013 07:06 PM
vinniekq2 the cam manufacturer will tell you the springs you need.
no speed shops in your area?
02-10-2013 06:53 PM
matt921 ahhh doo doo. Ok well I look into some other springs. what should I look for. I don't know how to read seat pressure an stuff
02-10-2013 06:33 PM
BOBCRMAN@aol.com Z/28 aftermkt springs will not work with that cam. In general they are only safe/good to about .490 lift
02-10-2013 06:25 PM
matt921
406sbc new cam 306s coil bind questons

So I recently bought a new comp 306s solid camshaft. I have some springs from a build I was going to do on a 350. So here is was I have now. Double hump heads, speed pro flat tops, 5.7 powdered rods. But to what my main question is.

The stuff I have now is the 306s cam solid The 306s is a .555 lift 306 duration 260 @050.solid lifters I bought from the performance shop in town. and a set z28 valve springs. Here is info on the springs o.d 1.260 I.d .880 seat pressure 110@1.700 90@1.750 open pressure 325@1200. So once everything is together It recommends .022 lash. I figure with .22 lash lift will drop to 533. This will hopefully put me into a safe limit on my springs.

Here is the main question if I do run into issues is there a way to get away from coil bind with out changing springs(building on a budget). I head that there are retainers that sit higher up on the valve stem. I hope I have put enough info to get some help. I know I kinda rambled on to sorry about that.

COMP Cams Magnum Solid Camshafts 12-225-4 - SummitRacing.com

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:38 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.