Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Small block chevy spark plug routing
User Name
Password
lost password?   |   register now

Thread: Small block chevy spark plug routing Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-20-2013 09:24 PM
rickman2k mine go down the tops of the valve covers
02-14-2013 03:07 PM
bigdog7373 Yea jegs will have what you need.
02-14-2013 07:49 AM
jims48 Thanks. I will check out JEGS too.

Jim
02-13-2013 07:16 PM
vht Jeg's has wire looms for under header routing. May be what you need. Anyone else that needs the long alum wire looms like mentioned above, google White Performance engines, they have alot of stuff like that. I got a 31 in alum rad for $110 that is real nice. Sharp fab polished valve covers for my sb chevy for $72 including shipping.
02-13-2013 04:02 PM
jims48 I like that idea. I checked out the Mr. Gasket looms. I can easily fabricate some aluminim brackets. I also like the idea of fabricating a couple brackets to drop down for fasteners. It is a little cold here yet and I have the exhaust manifolds off. As it warms up, I will try and make something that looks clean and works. When I get done, I will post some pictures. It may be something someone else can use. Thanks for the suggestions.
02-13-2013 09:28 AM
1971BB427 As you probably know, going above with plug wires and rams horn manifolds means the wires will get cooked where they lay on the exhaust. Best to keep them underneath as you planned, and use some brackets to drop down from the lower valve cover bolts.
You could get something like the Mr Gasket wire loom adapters #9870, and then instead of using the small 90 degree brackets to mount them above, make small aluminum sheetmetal brackets to locate them below the rams horn exhaust. Or just make the sheetmetal brackets to drop off the valve covers and tie the plug wires to a hole in the fabbed bracket. The aluminum sheet is easy to bend and cut into strips, and gives a nice finished looking support.
02-12-2013 05:35 PM
jims48 Thanks. I will look into this option as well.
02-12-2013 06:03 AM
malc This is tidy for me, going under the headers the wire will drop when you remove it from the plug.
This way I never mix up plug wires and you can remove the dist. cap and wires all in one lump.
R&M Billet Wire Looms 1102K


02-12-2013 05:39 AM
jims48 Thanks. Your suggestion is a possibility, but I was hoping to route the plug wires under the exhaust manifolds.
02-11-2013 05:17 PM
delawarebill
plug wires

have u tried the ones that are held down by the 2 bottom bolts of the valve cover.. more wire separators then anything..
02-11-2013 04:08 PM
jims48
Small block chevy spark plug routing

I am new to the forum. I am looking forward to sharing information and gaining some new knowledge and insights to the hot rod side of the hobby. I am looking for some guidance on routing spark plug wires in my 48 Olds. I have a small block chevy with a 1974 block. The previous owner used cable ties. I am looking for looms or shields that will work with rams horn exhaust manifolds. The 74 block I have does not have holes in the block to fasten the older shields. Anyone have any suggestions. Pictures would be helpful. Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.