Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Cleaning Ford 302 fuel injectors
User Name
Password
lost password?   |   register now

Thread: Cleaning Ford 302 fuel injectors Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-12-2013 02:51 PM
crownver If you don't want to have them professionally cleaned,
might be worth a shot. You can see what your spray pattern looks like too.
02-12-2013 01:50 PM
Silverback Apply power, does it click? do all the coils have the same resistance (older ones should be in the 11-15ohm range)? If they aren't then the coil is open and it needs to be replaced. If it doesn't click the pintle or disk is stuck, without a flowbench and ultrasonic cleaner you're unlikely to get it unstuck.

what works the best is to put them in an ultrasonic cleaner with a mixture of injector cleaner and mineral spirits while pulsing the injectors, then put them on a flow bench and flush the cleaning mixture forwards and backwards while pulsing the injectors.

Oh, you might want to replace the screens in the inlets too. Replacing o-rings and pintle caps is usually a good idea also, they're cheap.

Barring that you might have some luck just soaking them in a similar solution or if the car runs you might get somewhere by putting a good injector cleaner (the chevron stuff is pretty decent) in the gas at 2x the recommended concentration.
02-11-2013 11:22 PM
spinn Did the coil winding fail open in the soleniod.

Check the resistance in ohms.

If it needs new injectors get new. I dont buy into the cleaning and rebuilding. They spray fuel . Fuel cleans them.
02-11-2013 08:33 PM
Torque454
Cleaning Ford 302 fuel injectors

I think i have one fuel injector not working. I purchased a pigtail for the injectors, and a 9v battery (found something on google that said to use a 9v battery to activate the injector) and i used my mouth to blow air through (so far) 4 of the 8 injectors. I found one that air would not pass through. I suspect it is clogged since it clicks but wont flow.

How do I clean these injectors? Do they have to go to a shop or can I clean them myself? Any way to test the spray pattern? The air flow trick only tells me that the injector flows, not how well it sprays.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:52 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.