Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Bad valve adjustment
User Name
Password
lost password?   |   register now

Thread: Bad valve adjustment Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-14-2013 02:58 PM
bigdog7373 Go back and readjust the valves. All of them. Check all the wires. Pull the dist top and check for anything broken or any buildup. Pull all the plugs and see what they look like.
Also you need some spacers for those wheels. The offset is all jacked up, that's why nobody runs them.
02-14-2013 06:54 AM
vinniekq2 very nice looking car
make sure you retorque the wheels to make sure the new studs take a set.

re:#2, the wire is not touching the header,the plug is not fouled,and maybe take that cover off again,,,check valve movement and check spring for bind and or broken damper
02-14-2013 01:44 AM
cobalt327
Quote:
Originally Posted by dub View Post
Now I did run the "spit" test, and it was successful. The number two cylinder is not firing correctly. So I will adjust it tomorrow.
Nothing wrong w/adjusting the lifter preload w/the engine running, other than it's messy.

Hopefully the lifter and cam lobe isn't trashed. Over-the-counter motor oil can cause problems at cam break in time if there's no break in additive used like ZDDPlus, or if an engine break in oil isn't used. The lobes and lifter bottoms should also have been covered in moly break in lube.

But even then sometimes stuff happens and a cam/lifter will fail- sometimes because of idling the engine before the cam is broken in or because the lifter didn't rotate.
02-13-2013 10:52 PM
dub In case anyone was wondering what C5 rims like on a chevelle......
02-13-2013 10:47 PM
dub Sorry guys for the lack of info. I find it hard to give enough when I'm frustrated and just sank 2500 into a car that doesn't run correctly.
Info on the car:
Bored .80 over (apparently) Stroker, (apparently). I say apparently because I've driven a 383 stroker and mine does not compare to that.
Edelbrock performer airgap intake manifold, holley 650 DP. Flowteck long tube headers. "mild" rv cam.
Parts I just installed:::::
Here's the 2500 dollar part-
I just put a auburn pozzi carrier in, with 3.73 gears. New C5 corvette rims and tires, new wheel studs, all around, new front rotors with new brakes.
2" drop in the front along with monroe performance shocks.
(this is where the frustration begins.)
A couple of weeks ago, I started to hear what sounded like a exhaust leak. Turns out it was a lifter. Everyone knows that sound.
So I did the valve adjustment the old fashioned way. Popped of the valve cover, started the car, and adjusted accordingly. I know, I know, there are people that do not recommend the running valve adjustment. But quite honestly, I was impatient.
Now this is the weird thing, It ran like a raped ape for a couple of days, Then I went out to give er a run, and it wouldn't start. Finally got it started and it was misfiring badly.

So there is the back story.....Now I did run the "spit" test, and it was successful. The number two cylinder is not firing correctly. So I will adjust it tomorrow.

But hey, with the new rims, tires and drop....It sure does look good!!

Mike
02-13-2013 05:46 AM
streetrodderbn i have seen the need for readjusting the valves after the lifters pump up. Why did you re lash the valves? is this a new install, or were there problems with the engine that you felt the need to go through the valves again???? We need more info.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
02-13-2013 05:37 AM
engineczar Can we get a little more detail? Is it a stock 350 (stock cam/rockers) or does it have roller rockers, or an aftermarket camshaft? What year is the motor? etc.
02-13-2013 12:50 AM
S10 Racer
Quote:
Originally Posted by dub View Post
Defiantly a first for me. I guess I'll try that tomorrow.
Thanks
I use a spray bottle with water. If your engine has headers, start it up and let it run for a few minutes, 5-10 minutes should do it. Spray water on each header tube near the flange. If the water "boils" off, that cylinder is firing. If the water just runs down the tube or does not boil, that cylinder is either not firing or is firing very weak and need further attention. Do all 8 tubes and keep track of which ones are good and not so good. Post results when you know.
02-12-2013 10:58 PM
dub Defiantly a first for me. I guess I'll try that tomorrow.
Thanks
02-12-2013 08:25 PM
vinniekq2 see if they are hot.If you find cold pipes,those cylinders are not firingor if only warm then the cylinder is weak
02-12-2013 08:17 PM
dub For what reason may I ask?
02-12-2013 08:12 PM
vinniekq2 spit on all the header tubes when its running
02-12-2013 08:02 PM
dub
Bad valve adjustment

Hey guys!
I did a valve adjustment om my small block 350. Ran great for two days. Is it possible that it could be causing problems now? Went to take it to the store, and it barely start. Got it started finally, and it was miss firing really bad. Check all the basics as I could at the gas station, everything appeared normal. Any thoughts?
Thanks,
Mike

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.