Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Borgwarner T5 clutch questions
User Name
Password
lost password?   |   register now

Thread: Borgwarner T5 clutch questions Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-20-2013 09:17 AM
OneMoreTime Wow..always learning something..WE had to do the slip deal with an educated left foot in the old days..

Sam
02-20-2013 09:04 AM
logan1
Quote:
Originally Posted by aisr View Post
I've tested many a T5 to the point of failure. My experience is that anytime the durability of your clutch goes up, the durability of your T5 goes down.

3rd gear is most likely to fail, probably because it's narrower than 1st/2nd, and out in the middle of the case where a little flex will allow it to move farther away from the cluster. That flex moves the tooth contact area closer to the tips of the narrower teeth, making them more likely to break. A little clutch slip on engagement (and a lighter flywheel), will help smooth out those destructive torque spikes. Here's a link to info on an inexpensive clutch slipper that can help you get the most out of your T5...
Clutch Slipper Pics/info
OMG Its such a simple device but so freakin brilliant. Thanks for the link bro i think you just saved my T5 from getting destroyed a second time.
02-19-2013 09:30 PM
aisr
Quote:
Originally Posted by logan1 View Post
I have read a lot of the guys on the mustang forum saying that the spec 3 clutches can handle a lot of abuse and are very streetable. but ill do more research just to be sure.
I've tested many a T5 to the point of failure. My experience is that anytime the durability of your clutch goes up, the durability of your T5 goes down.

3rd gear is most likely to fail, probably because it's narrower than 1st/2nd, and out in the middle of the case where a little flex will allow it to move farther away from the cluster. That flex moves the tooth contact area closer to the tips of the narrower teeth, making them more likely to break. A little clutch slip on engagement (and a lighter flywheel), will help smooth out those destructive torque spikes. Here's a link to info on an inexpensive clutch slipper that can help you get the most out of your T5...
Clutch Slipper Pics/info
02-19-2013 07:53 PM
logan1
Quote:
Originally Posted by OneMoreTime View Post
In that case just run it until you see that replacement is needed...Then do the upgrade.

Sam
Well i don't want to put it all together and them have to take it apart a few weeks later to redo the clutch assembly.

So if I have to spend the money; Id rather do it now but if i can save a little money by reusing my pressure plate and just replacing the clutch without sacrificing the life expectancy of my clutch assembly i would like to do that.

Quote:
Originally Posted by S10xGN View Post
What stock bell works with a SBC and Ford T-5? Just curious if this is the Jeep/Astro van bell...

Russ
I using a stock camaro T5 bell housing with an adapter plate between the bell housing and the ford T5.

Quote:
Originally Posted by aisr View Post
I'd want an aftermarket pp with a pressure ring that can take the rpm, and a "high cone" diaphram that won't make the clutch pedal stick to the floor during hi-rpm shifts.

For the disc, i'd avoid the aggressive "spec 3" stuff and choose something that can handle some initial slip if you want the T5 to live. In my Chevy powered Mazda RX-7, i was able to get into the high 6's in the 1/8mi with the T5, using a stock style disc. Lite car with low gears, much easier on the clutch than a 3500lb Chevelle.
I have read a lot of the guys on the mustang forum saying that the spec 3 clutches can handle a lot of abuse and are very streetable. but ill do more research just to be sure.
02-18-2013 05:30 PM
aisr I'd want an aftermarket pp with a pressure ring that can take the rpm, and a "high cone" diaphram that won't make the clutch pedal stick to the floor during hi-rpm shifts.

For the disc, i'd avoid the aggressive "spec 3" stuff and choose something that can handle some initial slip if you want the T5 to live. In my Chevy powered Mazda RX-7, i was able to get into the high 6's in the 1/8mi with the T5, using a stock style disc. Lite car with low gears, much easier on the clutch than a 3500lb Chevelle.
02-16-2013 09:12 AM
S10xGN
Quote:
Originally Posted by logan1 View Post
thanx for the info but do i need to upgrade a pressure plate or can i run the current pressure plate with an upgraded clutch?

Also no i do not have a Scattershield sfi bellhousing yet. Just running the stock T5 bellhousing.
What stock bell works with a SBC and Ford T-5? Just curious if this is the Jeep/Astro van bell...

Russ
02-15-2013 04:15 PM
OneMoreTime In that case just run it until you see that replacement is needed...Then do the upgrade.

Sam
02-15-2013 03:55 PM
logan1
Quote:
Originally Posted by OneMoreTime View Post
As a general rule when I do a clutch I also do the pressure plate..Now if a customer is standing there with tears in their eyes and moths flying out of their wallet I will just replace the clutch disk for them..if I can go first class I get a new or rebuilt pressure plate clutch disk and have the flywheel surfaced. Up to you as to how to proceed..

Sam
Well the reason i ask is because my current pressure plate, flywheel and clutch have less than 10 miles on it and were replaced last month before i decided to do the engine upgrades. I know that the clutch needs to be upgraded but if possible Id like to atleast get some use out of my pressure plate before replacing it.
02-15-2013 03:37 PM
OneMoreTime As a general rule when I do a clutch I also do the pressure plate..Now if a customer is standing there with tears in their eyes and moths flying out of their wallet I will just replace the clutch disk for them..if I can go first class I get a new or rebuilt pressure plate clutch disk and have the flywheel surfaced. Up to you as to how to proceed..

Sam
02-15-2013 03:29 PM
logan1
Quote:
Originally Posted by OneMoreTime View Post
What you have done is very common in the engine swap world..Any of the guys who do custom clutched ca handle this. I would recommend an SFI pressure plate and clutch for you application and you do have a scattershield or sfi bellhousing I hope..

Sam
thanx for the info but do i need to upgrade a pressure plate or can i run the current pressure plate with an upgraded clutch?

Also no i do not have a Scattershield sfi bellhousing yet. Just running the stock T5 bellhousing.
02-15-2013 02:26 PM
OneMoreTime What you have done is very common in the engine swap world..Any of the guys who do custom clutched ca handle this. I would recommend an SFI pressure plate and clutch for you application and you do have a scattershield or sfi bellhousing I hope..

Sam
02-15-2013 01:49 PM
logan1
Borgwarner T5 clutch questions

Ok so i have a custom application for my 1970 Datsun 240z.

I am running a 355 SBC mated to a Borgwarner T5 out of a 1992 Ford Mustang 5.0. This means i have to run a SBC flywheel and a camaro pressure plate but the clutch has to come from a Mustang. I am in the process of upgrading my 355 with aluminum heads and a 292H cam. which should put me at about 400hp/400TQ.

I am currently running a stock mustang 5.0 clutch and a stock camaro pressure plate. I think i need to upgrade my clutch to handle the extar power the motor is going to be putting out and was wondenring:

If i upgrade my clutch to a perofrmace clutch do i also need to upgrade my pressure plate?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:41 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.