Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Stewart water pump issue
User Name
Password
lost password?   |   register now

Thread: Stewart water pump issue Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-14-2013 07:44 AM
61panhead Ok so I got the pump on too many holes! Sending unit goes in the left intake...any ideas on heater hose routing?

02-18-2013 01:15 PM
panhead1961 I didn't have another pump to go by but Stewart Components said the hole did not go any deeper because it would enter the casting. It had lots of slag left tn the hole. Didn't need it right away so waiting on the new one. I will post pics of the old and new together.
Thanks again guys!
Steve
02-18-2013 07:09 AM
496CHEVY3100 When you install the hose fitting the hole should align with the pump consider the thickness of the fitting it would have ben ok ,but since they are sending you another either will be ok ,I like good customer service,sounds like Srewart is customer freindly Thanks for post
02-16-2013 04:17 AM
panhead1961 I called Stewart Components talked to customer service and sent them a picture as well. They are sending me another pump and were Excellent to deal with! Will buy Stewart Components from now on.
02-14-2013 05:28 AM
Irelands child Stewart's were great when I bought a Ford pump for my car - I expect they will stand behind yours as well. All you should be out is some time. If you bought it through Speedway, same thing. I returned a set of poorly machined con rods not too long ago to Speedway - they supplied the no charge return UPS label. Again, I was out some time and a ride to the UPS store. Call them.

Dave W
02-14-2013 04:24 AM
panhead1961 Thanks guys, I thought it looked excessive. I have sent an email with the picture to Stewart customer service. I will contact Speedway as well.

Steve
02-13-2013 11:05 PM
gearheadslife mistakes happen, call them..
02-13-2013 09:22 PM
skippy89 my apologies, i just viewed the full picture on my lap top. that is a large amount of cast material. If you have the time to knock it loose and smooth it down with a dremel, then go that route. But you could just return it and say it's defective, and wait however long you have to for a new one to arrive. Because a blockage that large might cause you to overheat.
02-13-2013 09:16 PM
skippy89 All that is, is flashing from when it was molded. You can see the same material in the water passage of some new engines, as I did with my new small block. It's possible for it to come loose with operation, but unlikely to cause any harm in the form of plugging up the system. If you're really worried about it, just take a file or dremel to the flashing and get the loose material off. Then take a garden hose, or sink faucet and rinse it out. You can also leave it be, and wait for whatever actually wants to break loose, to come free. Then flush your entire cooling system, as a precaution, and simply preventative maintenance.
02-13-2013 07:47 PM
panhead1961
Stewart water pump issue

I bought a stage 1 Stewart water pump for my small block. I was shocked when I looked in the top hole, I could see where they drilled it, not all the way but that may be as far as they drill it but there was slag from the milling machine just hanging there. I tapped it with a screwdriver and clumps of slag fell out. May let them have it back! I don't have another pump to go buy so if any of you have a pump lying around please take a look to see if this is the way they drill then. If I keep it I will need to knock as much of that stuff off an possible and flush it.
Damn I get tired of ordering parts and getting the wrong stuff or just plain ****!


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.