Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> picking up a new engine today have some simple ?s
User Name
lost password?   |   register now

Thread: picking up a new engine today have some simple ?s Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-21-2013 11:36 AM
vinniekq2 If you are looking for a cheap sound and dont care about power,buy a thumper/voodoo,w/e.
If you want either a low lift roller hydraulic with a tight LDA,or a oval,short track limited lift race cam.
02-21-2013 11:14 AM
oldskool66 My car sounds great as it is i just want a cam that will give me the lobe at idle. just looking for some specs on a cam or a good part number that will work with the vortec heads and give me a nasty idle. as i really only drive my car on a trailer and off a trailer and a cruse once in a while.
02-21-2013 10:43 AM
vinniekq2 you can get a small roller cam with a lumpy idle.If sound is important,,,,
consider 3 inch exhaust with X pipe for the same reason.
02-21-2013 10:27 AM
oldskool66 im going to be running carb but i bought a thumper cam for my old motor and never put it in its for flat tappet so i thought i cant use it because the newer gm motors have roller cams. i paid 153 for it from speed way and was looking for something in that price range so i can exchange it.
02-21-2013 09:50 AM
picking up a new engine today have some simple ?s

After not being able to track down my masive oil leak and ive given up on that tired 307 im going to be picking up a complete pan to throttle body 96 vortec 350 with about 75k on it from a buddy for 400. i know i need a flywheel and intake for it. but my queston is what cam should i run i just bought a thumper cam from comp because i wanted that rough idle.

my specs for my 79 malibu are as follows

18x10.5 rear wheel with a 265/45/r18 tire

NV3500 5 speed with the 1st:3.49 2nd:2.16 3rd:1.40 4th:1.0 5th:.73

I have a 9" that i will be installing with 3.37 gears that i will be installing

2.5" dual exhaust no cats and 40 series flowmaster

I have 14" wilwood rotors with 4 piston calibers up front and 12"rotors with 4 piston calibers in the rear. i used the factory booster and a aftermarket master cylinder. (can run a vac pump if needed)

i dont drive this car often mostly just to car shows looking for lots of sound dont care about power much

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 07:47 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.