Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> scatter shield
User Name
Password
lost password?   |   register now

Thread: scatter shield Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-23-2013 11:05 PM
aisr
Quote:
Originally Posted by prostcelica View Post
The ground clearance thing is good as the car sits pretty low. I have the small fly wheel and starter already so it should bolt right up.
I'm thinking it might require a flywheel even smaller than 153T...
02-22-2013 11:06 PM
1Gary There is more details than just getting the bellhousing. You want a plate between the engine and the clutch to help protect the back of the engine too.
Without a mid plate with extra long dowel pins,you want in the case of a bellhousing failure,a cable to run under the engine to prevent the oil pan from dropping down on the steering linkage. If that where to happen,it takes a really bad day and turns it into a miscible day when you can't steer it. Grade 8 bolts only please.Really doesn't make much sense to have a bellhousing contain the explosion to have the bellhousing to block bolts shear off.Remember with a stickshift car and the shock loads your putting the drive train though,you'll only as good as the leakiest link.So the u-joints of the caliper of Lakewood's,to driveshaft loops,to a rear end that can take the shock load,to axles.

Now I know you didn't ask this question,but I think it is something you want to consider.You like anyone should be doing everything you can to get the car to hook.Stick shift cars are known for wheelstands.They might look cool,but unless your prepared for the track's largest wheelstand of the season,it will be the regret of the season for you.One thing I am speaking of is oil control and a trap door in the oil pan to prevent all the oil from rushing to the back of the oil pan. Of course a consideration for a front suspension that can survive a wheelstand without lost of control or damages.

I hope I gave you some help and food for thought.

Race or hot rod safe and in the end I hope you have the same fond memories I enjoy.
02-22-2013 06:55 PM
prostcelica The ground clearance thing is good as the car sits pretty low. I have the small fly wheel and starter already so it should bolt right up.
02-22-2013 02:22 PM
aisr It's 1/4" thick, but the bottom part is designed for ground clearance, so likely you have to use a smaller flywheel/starter.
02-19-2013 12:11 PM
crownver Thishttp://www.aascomotorsports.com/tilton/sonic.pdf site says it

"Meets 1⁄4'' thick steel requirements of many racing series"
02-18-2013 11:07 PM
prostcelica
scatter shield

Hey guys. I'm in the market for a scatter shield. I'm looking at buying the one in the link below from a friend (new in box). Its not SFI approved but I won't be quick enough for that to matter. I just don't want to get injured (or killed) if I have a clutch failure. My question is will this Tilton bellhousing contain a clutch failure just as good as a lakewood,Mcleod,etc ??

Tilton Sonic Formed Steel Bellhousings 12003 - Mobile SummitRacing.com

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:32 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.