Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Quadrajet geometry correcting plate for 700r4?
User Name
Password
lost password?   |   register now

Thread: Quadrajet geometry correcting plate for 700r4? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-25-2013 09:04 AM
artsvettes If it is not off a car with a 2004r or 700r4 trans, it won't work the geometry is diffrent
02-25-2013 07:24 AM
64r1 Thank you all for all your help!! I had a donor carb which is an auto so I'm going to attempt to just swap shafts because it has the linkage I need. Any precautions? Thanks again.
02-25-2013 01:04 AM
cobalt327 In some cases (on later model carbs), the baseplates can be swapped out- but you have to watch out for a few things, mainly that the gaskets are identical and that the idle air bypass orifices are similar. The bypass sizes aren't a big deal, they can be resized as needed.
02-24-2013 06:11 AM
artsvettes The later style quadrajets that were behind 700r transmissions are a good source. I swapped out the shaft of a 87 monte 2004r carb in my 77. It is a pain but it was less taxing on the brain.
02-23-2013 08:51 PM
cobalt327
Quote:
Originally Posted by 64r1 View Post
Then it must be!!! Motor came from automatic truck! Just asking for help. I'm sure I'm not the only one who has asked or been curious.
Q-jet carbs were used on some TV cable transmission equipped vehicles, using one of them will only require a bracket. A carb used w/a TH350 detent cable has slightly different geometry.

Info/links: TV cable
02-23-2013 03:23 PM
64r1 Then it must be!!! Motor came from automatic truck! Just asking for help. I'm sure I'm not the only one who has asked or been curious.
02-23-2013 03:13 PM
RWENUTS THen you must have a manual tranny quadrajet!
Excellent link Crosley!!
02-23-2013 02:46 PM
64r1 Thanks for some help I am actually away from the vehicle and cannot take a pick of my linkage so when I get back ill take a pic and post it it to thread. Those pictures on that site are good but the one picture shows the tv cable hooked to a hole in carb exactly opposite of the return spring hole. If I remember correctly I don't have that same provision for the cable just the return spring hole.
02-23-2013 02:38 PM
Crosley Near middle of page are fotos. May help

Clik Here
02-23-2013 02:27 PM
RWENUTS Search 'Google Images" for quadrajet tv cable and pick your poison.
02-23-2013 02:23 PM
64r1 I do not know where to begin with that diagram. I am sorry for my ignorance...
02-23-2013 12:59 PM
LATECH Here is a cartoon complements of Art Carr.
02-23-2013 12:46 PM
64r1 It's an automatic but it does not have the geometry plate for the tv cable
02-23-2013 11:56 AM
RWENUTS Is your quadrajet a manual or automatic tranny carb?
Auto tranny one has the bracket already on it.
02-22-2013 07:22 PM
64r1
Quadrajet geometry correcting plate for 700r4?

Ok I am sorry if I am beating a dead horse. I am having issues with my cable setup. I am running a 454 w 700r4 and the carb is a quadrajet my issue is the stupid geometry plate that attaches to the carb. I know they make aftermarket ones for holley, edelbrock, carter but yet to have seen one for a quad. Can someone help me please, I am so close to being able to drive the car in and out of the garage so i can start doing bodywork. Any input would be great! If someone knows how to fab one Ill pay to have one made lol. I know how important the tv cable is so I know not to drive it until all this is taken care of.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:14 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.