Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Help with Lathe
User Name
Password
lost password?   |   register now

Thread: Help with Lathe Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-28-2013 04:57 PM
spinn I got mine for 300. Never had any problems, and it works like any other. China is kicking butt.

Does it hold an alignment like a real lathe. No , but job to job is fine.
02-28-2013 04:38 PM
1971BB427
Quote:
Originally Posted by spinn View Post
Harbor freight sold very reasonable units.
Reasonable, but sloppy. I have one that's a benchtop unit, and it isn't any good for any precise work. Cheap Chinese junk, but I bought it for roughing out small parts and still had to tighten it up, even for rough work.
02-28-2013 04:25 PM
Richiehd As usual, lots of great help on this site, thanks guys!
02-28-2013 04:24 PM
spinn Harbor freight sold very reasonable units.
02-28-2013 04:08 PM
1971BB427 South Bend is a favorite of mine, and Grizzly bought South Bend a few years back so they could gain access to their technology for the Grizzly brand lathes. For a new lathe the Grizzly is a very nice lathe too.
Be sure whatever you get has at least a 3/4" bore, but a 1" is even better! The advantage of a used lathe is you can usually get a lot of extra tooling with it for the same price. One of the disadvantages of buying from a used tool peddler is they will pull all the extra tooling and then sell it back to you as extras. I'd rather buy from a private party and take someone along who's got a good background or knowledge in lathes to make sure you get a good one. Then you can get it before a middle man pulls the extra tooling out.
02-28-2013 11:17 AM
69lm69gp mrpete222 (aka Tubalcain) on youtube has some videos on what to look for when buying a lathe as well as how to run them. I suggest you start there.

I have a 1936 9" South Bend myself. South Bends are very common and Practical Machinist as a fourm section for them with a lot of usefull information on fixing them and maintaining them. The PM fourm also has sections for other makes as well depending on what you find.

Tubalcain Youtube link
02-28-2013 08:36 AM
OneMoreTime Grizzly machine makes some decent tooling..It is import but works fine. Check on pricing of new equipment to get some ideas of what those go for. Sometimes a big lathe is cheaper to buy as the smaller "hobby size" are in great demand when looking at used.
I would like to have one big enough to turn a crank in myself. Always can do smaller things..


Sam
02-28-2013 08:23 AM
S10xGN I've got a pre-war Atlas 12x36 with a 6" 3-jaw chuck that does just about anything I need. My only "complaint" would be the inner diameter of the headstock is too small to allow anything long to pass through it. I also upgraded the 1/4 HP motor to a 3/4 HP. I've seen these on E-Bay for around $1k in good shape...

Russ
02-28-2013 07:32 AM
BOBCRMAN@aol.com Logan, Southbend, Atlas (Craftsman), LeBlond, Sheldon, Jet are all great brands of toolroom lathes. Avoid turret lathes and special purpose lathes.

I would rather have an older bench lathe than the newer hobby China junk. Better bearings and lasting tollerances.
02-28-2013 07:21 AM
Mr. P-Body "Jet" is a very popular "home size" unit.

I've seen some old Craftsman (yes, from Sears) units floating around, too. I agree, check with a "used machine" supply house. Another option is to look in the Dayton, Ohio area, as that's been termed a "Mecca for used machinery".

Get at least an 8" chuck. If you can find one that's NOT "3-phase", it will be easier to install at home. "Phase converters" are available, but a bit pricy...

Jim
02-28-2013 07:01 AM
35terraplane You can sometimes find them on Craigs list, but If it were me go to a used machine dealer. you might pay a tad more but you will get a checked out machine, I would also get a machneist lathe.

Bob
02-28-2013 06:08 AM
Richiehd
Help with Lathe

I am looking for a metal lathe to put in my garage at home. I think I want used, but not sure what brand etc. to look for. Im looking to be able to make and modify small pieces. The biggest I might need would be to hold a 4 inch piston. Any ideas out there? Some of you guys must have a lathe in your garage. Where should I look other than Ebay?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:24 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.