Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Carburetors, CFM and Dual Superchargers
User Name
Password
lost password?   |   register now

Thread: Carburetors, CFM and Dual Superchargers Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-05-2013 02:45 PM
zoomzu
Quote:
Originally Posted by zoomzu View Post
It's an Eaton M90 mine came off a 3.8 Pontic Bonneville.
My bad
Fixed
03-05-2013 10:00 AM
johnnyg
Quote:
Originally Posted by 68NovaSS View Post
When did Buick make a Bonneville??
I had a Bonneville with a Buick engine in it! LOL
03-04-2013 11:27 AM
zoomzu
Quote:
Originally Posted by xxllmm4 View Post
I just used steel plate and square tubing to make an adapter that fit on the intake.
That's my basic plan too. I may convert to propane also.
03-02-2013 08:57 PM
68NovaSS Your two threads, same subject matter, have been merged. If you don't have questions in a thread, consider posting in the projects forum, but don't expect answers to any questions, it's a show n' tell forum.
03-02-2013 08:19 PM
HunterJ Thats awesome !!!
03-02-2013 07:51 PM
xxllmm4
Dual superchargers thread

I figured I would start a new thread on this. I snapped a couple pics of how its put together. Pretty simple to do with just a chop saw and welder.
03-02-2013 07:35 PM
xxllmm4 Ohh yeah one more thing, the snout oil seal, they wear out and start to leak. They make 2 kinds. A rubber seal and a viton. I don't recommend the viton, its harder and will actually wear a groove in the steel shaft. The rubber also seals better on worn parts.

The seals are also off the shelf parts. You just need to know the numbers and where to find them at industrial supply houses.
03-02-2013 05:44 PM
vht Are they making a better Pred carb now? I know yrs ago they were hard to get dialed in and when you did they kinda had a mind of their own on how they were going to idle. This sounds like a cool build. Friend of mine had a Grand Prix, 3.8 work car he played with. It had alot of miles, pretty rough looking, but wouyld run high 12's slicker than hell. You ought to have seen some of the looks he got when he would smoke a newre Mustang.
03-02-2013 01:37 PM
xxllmm4 About the only thing you really need to look at are the rotors/case. If they are scratched toss it. The most common problems are as follows.

1. Plastic coupler inside the snout wears out, causing a clunking sound. New ones go from $15-25 always replace them if you have the blower opened up.

2. Front snout bearing, then second snout bearing. Easy to replace and cheap. You just need a shop press.

3. Rear rotor bearings. Depending on the model you may need to drill and tap the blower housing, add zerk fittings and pump the bearing out with grease. not hard to do. Bearings cost about $3-4 ea.

4. Front rotor bearings. These can be difficult to replace. Sometimes the housing will break when they are pressed out. 95% of the time these bearings are fine and don't need to be touched.
03-02-2013 11:52 AM
68NovaSS
Quote:
Originally Posted by zoomzu View Post
It's an Eaton M90 mine came off a 3.8 Buick Bonneville.
When did Buick make a Bonneville??
03-02-2013 06:35 AM
64nailhead What is the inspection process for an M90 in terms of determining if it is good, bad, or rebuildable? Maybe someone has a link?
03-02-2013 12:35 AM
xxllmm4 It looks like we left the camera at the in-laws tonight so I will try and remember to snap some pics in a few days.
03-02-2013 12:33 AM
xxllmm4 I just used steel plate and square tubing to make an adapter that fit on the RPM Air-gap intake.

I actually did make an adapter to run a single carburetor on it but the gas pooled and I gave up on the idea. I needed to get it running and just took it all off. I'm defiantly going to get it going again one of these days. For me, I enjoy the fabrication end and hate the tuning.

These blowers have LOTS of potential on 4 bangers, straight sixes and V-8's. I used to rebuild and sell Eaton blowers till the pick N pull tripled their prices. Everything inside uses cheap off the shelf parts, bearings, seals ect.

The design probably isn't the best but keep in mind I asked for help on many message boards and most of the time all I got was go buy a kit.
03-01-2013 06:59 PM
spinn Great job . How hard was the base plate to fabricate? What did you use?

Most of these eaton blowers are plentiful and cheap. Nice to see people using them.

The edelbrock carbs sound like a good idea to me too.
03-01-2013 06:48 PM
bigdog7373 God that's awesome! How about using 2 500cfm eddelbrocks?
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:27 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.