Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> trying to estimate horsepower and torque slightly built 440
User Name
Password
lost password?   |   register now

Thread: trying to estimate horsepower and torque slightly built 440 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-02-2013 09:18 PM
snakebit68
HP estimate

You have confused me a bit with your parts list and question. Propane will get different results from a fuel system. Conservative estimate for HP with domed pistons and stock heads...which will be restrictive in flow...will be around 350HP...especially with the cam. May be difficult to get your mix right with the current list of parts. Needs different heads and headers for sure. Propane likes to breathe.
03-02-2013 08:21 PM
vinniekq2 dual propane mixers with a turbo?
03-02-2013 08:12 PM
bsfor thanks for all the replies.

I'm trying to find the info on the compression ratio but I have searched and searched and found different answers.

I have had this motor for a while trying to build the rest of the vehicle.

Let me give a little more info:

It will be run on propane. that was the reason for the cam choice. I remember my motor guy telling me that the pistons I got were domed and would give me a compression ratio of about 10.4:1 Not sure if that is right. but I know that the compression was supposed to be above 10:1. Propane likes high compression since it is on average 108 octane depending on where you buy it.

it will be running the stock exhaust manifold to begin but eventually it will have headers, I was worried about it running out of air so I plan on running this setup for the propane:

IMPCO Propane Dual Twin 2 CT425M 2 425 Holley 4 bbl Throttle Plate 600HP LPG Kit | eBay

Since I already have the two 425 carbs.

Let me know what you think.
03-02-2013 08:04 PM
vinniekq2 lots of 550 hp 440s,in my neighbourhood,bring more. We tried a purple cam in a pick up,it needs more Compression than a pick up 440 has.top end was good
03-02-2013 03:11 PM
LATECH Just a WAG I would say 290 -320. Cam seems small .I would have opted for a cam in the 215 -224 at .050 lift range.
JMO.
You could run a purple cam, but you would need a bit more compression than those 1973 smogger heads will provide.

Glad to see a MOPAR guy around here.
03-02-2013 01:24 PM
bsfor
trying to estimate horsepower and torque slightly built 440

I have a 440 from 1973 that cam out of a winni. I took it to my mopar motor guy and he said it had the good crank and rods. I had him bore it .30 over and installed these pistons
Speed-Pro Forged Pistons ZL2295F30
Speed-Pro Forged Pistons ZL2295F30 - SummitRacing.com
and this cam
COMP Cams Xtreme Energy Camshafts 21-220-4 - SummitRacing.com

it has stock 452 heads on it and stock 4 barrel intake.

I'm trying to guestimate the HP and Torque

by the info here what would you guess?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:55 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.