Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Effective volume on piston
User Name
Password
lost password?   |   register now

Thread: Effective volume on piston Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-15-2013 01:58 AM
cobalt327 SBC true FT w/4 valve reliefs are between 5 and a bit more than 6cc.
03-14-2013 01:14 PM
hcompton Most four vavle reliefs without the dish are 6 to 12 cc's But the deck hieght is the most important here. Zero deck or .045 in the hole makes a big difference.
03-14-2013 10:07 AM
lg1969 I use this cal
03-13-2013 05:43 PM
KyleG Hard to say. Its running fine though. I'm just gonna drive it lol Drives smooth, pulls smooth. Sometimes may have a little bog. But thats part of it I guess
03-09-2013 10:44 PM
cobalt327
Quote:
Originally Posted by KyleG View Post
I dont think the heads are shaved any, and stock spec head gasket. Filled up on regular and can't tell a difference. So probably around 9:1 thankfully lol
You have a 1 point range of between about 9.2 and 10.2:1 depending on the block deck, gasket thickness and whether the pistons are 1.56" or 1.54" compression height.

The problem at the low end of the CR shown is the quench distance will be VERY wide (as much as 0.086" w/a 0.045 piston deck caused by a rebuilder piston combined w/an unmilled deck along w/a 0.041" gasket thickness).

As long as it'd not detonating, at least it shouldn't beat the bearings out of it or pinch a ring.
03-08-2013 07:09 PM
KyleG I dont think the heads are shaved any, and stock spec head gasket. Filled up on regular and can't tell a difference. So probably around 9:1 thankfully lol
03-08-2013 04:57 AM
BigMo Yeah, youre like 9-1 or so....those 4-brow pistons have like 6 to 7.5 cc loss of volume....and with that large of a deck (.030) you are down quite a bit......unless the heads are shaved to the max and the chambers are like 62 or something w a really thin head gasket.....
03-07-2013 08:53 PM
KyleG Its just a real bad photo, it was a little carbon build up..
03-07-2013 08:45 PM
painted jester that #3 piston (2nd one back) looks like its got a bad spot above the ring land at 2 o clock is it damaged or just a bad photo? These eyes are old!!!

Jester
03-06-2013 08:08 PM
KyleG
Quote:
Originally Posted by ap72 View Post
Maybe. Maybe not. The joys of messing with a "mystery engine"
Very true!
03-06-2013 07:57 PM
ap72 Maybe. Maybe not. The joys of messing with a "mystery engine"
03-06-2013 07:54 PM
KyleG Goood! Soo regular gas is goood to run??
03-06-2013 07:50 PM
BOBCRMAN@aol.com Nowhere near 10-1. Those pistons look like rebuilders pistons, note the large double valve reliefs and front large notch. All bleed off compression. Plus most rebuilders pistons are .020" short
03-06-2013 07:45 PM
KyleG No idea man. Its already thrown together.. /: And I was thinking it was that low.. Hoping it was haha Cheaper gas. Been running 93, because I thought it was higher than 10:5
03-06-2013 07:42 PM
ap72 You're probably closer to 9:1. What part number is on the pistons?
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.