|04-10-2013 08:53 AM|
Any recommendations for spark plugs? My head card casy i need a plug with 3/4" reach. Was thinking about buying a set of Champion RC12YC.
|04-05-2013 09:51 AM|
Patriot 23 Deg 185 Out of Box CHW SF600 Alum 185/- 2.02/1.60 N/A
0.1 0.2 0.3 0.4 0.5 0.6 0.7
56/53 101/83 147/114 190/137 227/155 245/171 248/177
This didn't copy and paste too cleanly but its flow numbers for the patriot 185's. Depending on application a single pattern cam would not be out of the question.
|04-05-2013 09:28 AM|
If you go to headbytes.com he had a cylinder head shoot out using pro comps, patriots and brodix. I found it interesting but those heads he has came in last.
|04-05-2013 09:22 AM|
if you dont know the flow numbers red
with a less than 70% exhaust flow ratio you still wont ude a dual pattern cam?
|04-05-2013 09:17 AM|
|04-05-2013 09:14 AM|
|04-05-2013 09:09 AM|
|vinniekq2||red,are you recommending a hydraulic roller tappet cam?He said way back that a roller is out of the question|
|04-05-2013 08:57 AM|
|03-26-2013 04:56 PM|
|03-26-2013 04:01 PM|
I get guys who do this and then want the $6000 trans under warranty.
You slip the clutch. The disc is cheap, and easily replaced.
|03-26-2013 10:45 AM|
You will most likely find the most gain by just using the 1.6's on the intakes only.
The exhaust side responds more to duration changes than lift changes.
The changes will be small at best.
You can play with the lash too. start at a cold setting .004" less than the hot lash spec.
If/when trying a bigger lash setting do not get carried away.
You need to change your reference from a how much power for this and that bla bla bla to a reference of actual tested +/- improved performance by trying different stuff like lash and rockers.
That cam is small as cams go and will probabily respond well to running less / tighter lash than spec valve lash if you want horsepower.
less lash results in increased running valve duration. (makes the cam act slightly "bigger")
|03-26-2013 10:24 AM|
Sorry to bring this thread back from the dead but i figured it would be better than starting a new one. My greed / eternal quest for more power is kicking in and Im now thinking running the 1.6 rockers is a good idea as suggested by F-BIRD.
I have already ordered the cam from summit: Mechanical Flat Tappet 275/281,.505/.520
Howards Cams Mechanical Flat Tappet Camshaft and Lifter Kits CL110102-06 - SummitRacing.com
So I will have the following lifts:
Intake (.505" x 1.0666) - .022 = .517
Exhaust (.520" x 1.0666) - .022 = .533
How much power gain can i expect with this change?
Also below is a picture of my short block ready to go back together. The cam i ordered is on backorder and will probably get here in the 2 week of april.
|03-19-2013 10:31 AM|
Summit cams look cheap and use older grinds but really nothing wrong with them. But they are also not the best grind for long life. USally what you are paying for is not quality manufacturing but good design. Go with a good design price is mute once its whiped and the entire engine needs to come apart to clean and replace.
Here is a link about cams. FYI the companies mentioned are owned by the same people.
|03-19-2013 10:27 AM|
This will surely make your car slower and increase the heat in the clutch and kill it faster. Best to just drop it. I move my foot sideways off the clutch not up. A slipping clutch can be killed in a day one that is dead locked will last its service life.
Drive line shock is best delt with in other ways.
|03-19-2013 10:26 AM|
|Landshark928||I would pass on a Chinese cam since USA cams are not much more. Assault line is rebranded Pro Comp. look at Summit brand came if you want to save a buck.|
|This thread has more than 15 replies. Click here to review the whole thread.|