Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> pinion angle
User Name
Password
lost password?   |   register now

Thread: pinion angle Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-09-2013 12:27 PM
RWENUTS Make them equal. Tranny 3* down, pinion 3* up.
Your rearend needs to come up 6*.
When setting up a new rearend don't tack the perches on until you have the rearend sitting at ride height on the ground. Set the pinion angle, tack it into place, remove and finish weld.
Here's a link on pinion angles.
Pinion angle? - The 1947 - Present Chevrolet & GMC Truck Message Board Network
03-09-2013 10:41 AM
57SteveChevy
pinion angle

here are pictures of the trans angle and the pinion angle this morning!
03-09-2013 10:38 AM
57SteveChevy Good morning everyone! this morning, the angle on my transmission is between 2 and 3 degrees down, the angle on my pinion is between 3 and 4 degrees down. I tacked the perches on level with a 3 degree angle up but now installed these are the results, looking at these I am thinking I need to reweld the perches level with a positive angle of 8 to 9 degrees to level the line from trans to pinion, any thoughts? Thanks again for the help!!
03-08-2013 10:37 PM
SSedan64 Pinion angle
Pinion Angle - Wolfe Race Craft
03-08-2013 07:17 PM
evolvo Some light reading to get you started

http://www.iedls.com/asp/admin/getFi...&TID=28&FN=PDF
03-08-2013 05:54 PM
2speed_1
pinion angle

It will be fine as long as its 3 degrees down. most rear ends have that built into them already (angle of leaf spring perch).
03-08-2013 05:33 PM
57SteveChevy
pinion angle

I am new to the site and am in need of some help! I have a 57 3100 and I am installing a 79 Camaro rear end, my question is, does anyone know how many degrees of angle to set the pinion at keeping in mind that my truck still has the stock height and stock leaf springs? Thanks for any help you can give me in advance!! I am attaching a picture of what the angle looks like now at 3 degrees, let me know what you think!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:56 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.