Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 700r failure
User Name
lost password?   |   register now

Thread: 700r failure Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-19-2013 07:28 AM
BigMo WORN??!!! Id say tore up to the will need complete tear down.....and trying to get all the metal out of those passages will be damn near impossible....oh, dwwl just said that....but anyway...its toast man
03-18-2013 08:48 AM
dwwl I would also bet that there is so much metal in everything that, that if you rebuild it, it just will cause you more problem later. So, buy a good use one, and use it, or rebuild it and use your old one for the parts you might need for the rebuild. I bought one used 200 r4 from a local guy of CRAIGS list for $75.00. One from a guy i knew for $75.00. Then I had a guy give me a bad one for parts. That bad one worked out great. I then had extra things to experiment with.
03-14-2013 01:54 AM
mmerlinn And one more thing. Your valve body is full of metal. It will probably be easier to replace it with a different valve body than trying to clean up your old one.

If it were me, I would probably try to find another transmission and rebuild it instead of that one. Of course, that may not be possible, so good luck with fixing yours.
03-13-2013 07:42 PM
Kawabuggy When I look at damage like that I have to wonder how long somebody drove that vehicle whilst the planetary set was grinding itself into dust.

Yes, the trans can be repaired. Throw the planet, reaction shaft (ring gear) & sun-gear, & plastic thrust washer (between sunshell & sprag race) all in the trash. Tear the entire trans down and wash it until there is no metal left inside the case, or any of the parts. You will need a complete clutch set as there is metal imbedded in all of them by now. You will need a band. You will need a complete bushing kit. You will need to disassemble the governor and remove all metal from the barrel and polish the gov. valve by chucking it in a drill and holding it against 1000 grit paper. Replace all the screens in the case-2 of them under the valve body, and 1 in the pump. With that much metal in the trans, your pump will probably be scored. Your trans cooler inside your radiator is probably littered with metal. Get an external cooler and bypass the trans cooler if you can't get it flushed of all metal. You will need a new converter. You will need a bearing kit as I would not risk running any of the bearings now that they have metal inside them.

More importantly-what caused this? Pull the seal that rides inside the 3rd & 4th clutch drum. It will be under the bearing that the input sprag assembly rides on. Is it a hard plastic seal? My guess is that it is/was. It is probably damaged and caused a lack of lubrication to the rear planet set. When you rebuild it, if you rebuild it, DO NOT use a hard plastic seal there. Ask for, or order, a Viton seal as is used in the 4L60E's. Good luck with your transmission.
03-12-2013 07:15 PM
700r failure

I need help! I have a 86 c10 and my transmission won't get reverse or up shift from first, I tore it down and the rear planetary gear is worn and there was a lot of metal in the pan but every thing else seams ok, what other damage should i look for and can it be repaired?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 09:02 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.