Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> ring gear spacers, good or bad
User Name
Password
lost password?   |   register now

Thread: ring gear spacers, good or bad Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-21-2013 08:43 AM
lmsport I've 12 bolts with all 12 sheared off without using a spacer.
I used to replace them with some super high strength studs, back when some fast cars ran 12 bolts.

Spacers are never the preferred solution, but then again, neither are axle repair bearings or yoke seal Speedi-Sleeves.
03-21-2013 08:12 AM
BOBCRMAN@aol.com "This causes the ring gear to float on the differential and only the bolts hold it in place. This causes contact pattern problems. I have seen several 12 bolt rear ends that sheared the ring gear bolts off because of a ring gear spacer. Ring gear spacers are a bad idea and should be avoided. "

Yes, these are very old school, but back in the day. Spacers are what we had and I saw a few rears that sheared the bolts off clean.

I had a customer with a 70 Impala with a 427 BBC and 4 spd. Was real hard on drivetrain parts. Sheared the bolts on first drag race..
03-21-2013 08:09 AM
dwwl I think using the spacer is not going to be a good idea. I did that once on a 10 bolt and it didn't go well. It worked fine for regular driving, but i had a very unusual abnormality of having a very large/heavy right foot. I won the race, but spent alot of money replacing the entire rear housing. Was expensive.
03-21-2013 07:49 AM
big gear head I've seen a lot of problems with ring gear spacers. They move the ring gear away from the flange on the differential where there is a machined sholder that centers teh ring gear. This causes the ring gear to float on the differential and only the bolts hold it in place. This causes contact pattern problems. I have seen several 12 bolt rear ends that sheared the ring gear bolts off because of a ring gear spacer. Ring gear spacers are a bad idea and should be avoided.

You can get a 3 series Eaton Posi case and transfer all of the parts from your 2 series Eaton Posi into the 3 series case.
03-21-2013 07:14 AM
lmsport Spacers are OK for everyday driving, but not in a high performance application.

There are three carriers for both the 12 bolt car and 12 bolt truck.

With a standard gear, 3.73 is used with a three series car carrier or a four series truck carrier.
03-21-2013 05:43 AM
BigMo In my opinion, BAD....get the right series carrier, I think a 3 series will work with the 3.73's. There is a threshold where you have to go with the #4 carrier, I think its when going to a ratio higher than that....someone chime in here.....I put together many 12-bolts, but never went that high on the gearset, was always into a low ratio (4:10 and lower)
03-21-2013 05:36 AM
actmobmar
ring gear spacers, good or bad

i picked up a 12 bolt posi w/ 2.73 gears and i'd like to put 3.73's in it, is it ok to use a ring gear spacer or am i asking for problems? thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.