|03-22-2013 08:31 PM|
|rick 427||I don't like the idea of the spacers....If you do it that way,most of the trans case is away from the motor.And when you go to put the crossmember in,you have to raise the weight of the trans and the back half of the motor up to get the crossmember in.I would be concerned that the trans bell might[strong emphisis on might] break.So,here's what I would do if i felt better having the trans in during break-in.Bolt the trans to the motor the conventional way. Leave the torque converter in the box it came in. When your happy with the motor,pull the trans,and proceed with the proper installation.Whaddy ya think?|
|03-22-2013 07:32 PM|
My other thought was to simulate your screwdriver method by placing some flat bar stock bolted between the block and housing and extending in front of TC, bent so that pushes it back like a big flat finger. I saw this in my book.
|03-22-2013 08:12 AM|
|rick 427||SS...no problem,happens to the best of us....As far as the spacer thing..if you are going to space it back to break in the motor,then unbolt the trans again to remove the spacers,whats the purpose of even having the trans there in the first place? Why not just leave it on the floor until the motor is all squared away,then put the trans in? Even with the spacers,there is no guarantee that the TC won't walk out of the trans that little bit while the motor is running.When we disconnect a TC from the motor to isolate a vibration issue,1 person has to be under the car with a large screwdriver to hold the TC into the trans to prevent it from doing this while the motor is running,or sure enough,it will work its way back towards the flywheel.And our run time is only a matter of seconds.|
|03-22-2013 07:59 AM|
Rick, thanks for correcting my Startup mistake, fingers & brain weren't syncronized.
Jtraik, yes, you can use Spacers/Washers if wanted/needed for additional clearance between the Engine & Trans bellhousing during breakin. It is difficult to monitor both simultaneously.
TC to Flexplate clearance should be 1/16" Min. to 3/16" Max. after tightening Bellhousing bolts.
|03-17-2013 02:59 PM|
Thanks for the procedures! I was able to fix my drum clearance issues and got 5 disks in the forward and 6 in the direct by putting a friction disk right next to the wave. I then ended up with about 0.055" for both, so I am pretty happy.
Another question pertaining to the fluid and initial start up. The engine is freshly rebuilt and needs a break in (first time for this as well). I want to have transmission in the vehicle for break in. Can I leave the torque converter separated from the flywheel and break in the engine? In my book he is very clear that the space between flywheel and converter should be about 1/8", this seems awfully close to have that flywheel spinning at high rpm while the TC is at rest. Can I space the bellhousing to the engine to give me another 1/2" so that I feel comfortable breaking in the engine before going forward with the transmission procedure?
|03-16-2013 12:46 PM|
|rick 427||Whoa....pour 1 qt into torque converter before you put it into the trans...Install the trans...Pour 4 qts into trans...With rear wheels up in the air,start the car in park,DO NOT shift into any gears at this time,as that trans is still at least 6 qts low yet on fluid...Nothing good ever happens when a trans is run while low on fluid...leave it in park...Immediately pour 6 more qts in it after start up....Start checking the fluid level at this point and add until It's full.....NOW, you can run it thru the ranges...check fluid again....road test,and then have 1 more look at the fluid level.That trans will take around 11-12 qts, total, with a stock converter.|
|03-15-2013 10:16 PM|
Generally .010" clearance per Friction.
Some Forwards use 4 Frictions some use 5. Should be fine.
Pour 1qt. in TC/Torque Converter, pour 4qt. in Pan, with Rear on Jackstands start engine, shift thru gears, add fluid until it shows on the Dip stick, shift thru gears, add fluid untill it's at the Cold Mark, top off to Hot Mark when the Engine/Trans is up to operating temp.
Automatic Transmission & Torque Converter Fluid Capacity - TCIŽ Auto
Torque Converter Installation Instructions
|03-15-2013 08:15 PM|
T400, looking for answers before install!
I am wrapping up my T400 rebuild finally and hopefully will do the install tomorrow morning. The application is a nearly stock ~400hp (at flywheel) Cadillac, just doing a resto. I had a few concerns after finishing setting up the drums.
1: To get a 0.060" clearance in my direct drum I had to go with mostly thin steel plates in addition to the wave. From what I read this is a good clearance but will I have any heat issues with mostly thin steels?
2: My forward drum, with a wave, only took 4 frictions and to achieve 0.060" clearance. Is that friction disks enough for it?
3: I have never installed a dry transmission, whats the procedure for filling it with fluid in regards to the install? Can I put all the fluid in after it is installed?