Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> SBC 195 degree Thermostat
User Name
Password
lost password?   |   register now

Thread: SBC 195 degree Thermostat Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-29-2013 08:22 PM
gonzo08383 my motor is almost the exact same specs as yours except i run a comp cams thumpr. i have to run 93oct or i get pinging bad. try the hotter t-stat and drill a small hole for bypass. a regular mr gasket should work fine for the experimentation. hotter is more power and if your radiator can keep up you should be happy with the results
03-26-2013 06:52 PM
fastnloud Thanks, I think I may try one of the Stant SuperStat 180's.
03-26-2013 12:04 AM
acme
180 - 195

Quote:
Originally Posted by fastnloud View Post
In my truck with a with a built 350 SBC, would it be good to run a 195 degree thermostat, and is it likely to cause detonation? I've been reading about how it may run a bit more efficient with a 195 T stat.

Thanks guys.

From experience I tried the 160, but a 180 or 195 ran smoother and it's better for the oil so it can burn off contaminates , condensation in your oil. Oil likes higher temps anyway.....An efficient radiator will keep a steady temperature that helps too.






03-25-2013 05:55 PM
fastnloud Thanks, I was actually looking at one of the Mr. Gasket hi flows, but you wouldn't recommend them?

The Stant SuperStat is cheap, but if that's a good one, I can just go ahead and get that.
03-25-2013 12:38 PM
Bonneville462 I had trouble with both Mr Gasket and Robert Shaw pill style thermostats.. I ended up pitching all that expensive junk and using the regular old Stant t-stat..

I get the smallest drill bit I have in my box and drill one hole through the stat.. Looks like Stant does a similar thing with the V notch..
03-25-2013 11:37 AM
fastnloud Also, this stant is suppose to be better, but it's also cheaper.
Stant SuperStat Thermostats 431-45358 - SummitRacing.com
03-25-2013 11:26 AM
fastnloud I'm getting a bit confused, I was going to buy a robert shaw t stat, but you supposedly can't use them with a stock style water pump.

So, what about Stant, are they good?
I was looking at this one.
Stant Thermostats 431-14218 - SummitRacing.com
03-25-2013 10:46 AM
fastnloud My compression is around 10:1, I think. I'm thinking I may go ahead and try one of the Stewart hi flow 195's.
I just hope it doesn't cause any detonation.
03-25-2013 06:50 AM
Bonneville462 I'd try it, it is defiantly a tuning tool.... Heat is power...

My Pontiac 462 likes the 160 and runs better on 89 octane then having a 190 with preimium.... I had to experiment with it though...
03-24-2013 10:14 PM
fastnloud Thanks for the help, here are the specs on my motor, maybe that can help with recommendations

350 4 Bolt Main .040 Over
Scat forged I beam rods
Keith Black flat top pistons 4v reliefs
Moly rings
World Sportsman II heads 2.02 valves and 64cc chambers
Edelbrock performer rpm intake
Holley 750 carb
1 7/8 longtube headers
Lunati Bracket Master II Cam 300 duration
Crane Valve springs
Crane roller rockers
Comp Cams double roller timing set

Also I run 93 octane fuel.
03-24-2013 09:57 PM
gonzo08383 depends on your compression ratio, iron/aluminum heads, octane of fuel, and lots of other stuff. my 350 loves 195*, it really rockets up. i also have to keep premium fuel in it and if it sits too long i have to put additive in the fuel or it will try to run backwards when i shut it off. i say try it out and see what happens. its not like its going to blow up and a t-stat is under 20 bucks. i'd turn the timing down a couple degrees just to be safe tho.
03-24-2013 08:32 PM
fastnloud
SBC 195 degree Thermostat

In my truck with a with a built 350 SBC, would it be good to run a 195 degree thermostat, and is it likely to cause detonation? I've been reading about how it may run a bit more efficient with a 195 T stat.

Thanks guys.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:16 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.