Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Source for bandsaw blades?
User Name
Password
lost password?   |   register now

Thread: Source for bandsaw blades? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-25-2013 09:20 AM
boothboy The last band saw blade I got from Grainger's. Another place iI wouldn't hesitate buying from is Grizzly's. I just bought some shaper cutters from them. Excellent quality.

BB
03-25-2013 09:02 AM
vpd66 I've had good luck with Lenox bandsaw blades. I get them at my local Fastenal.
03-25-2013 07:34 AM
suzidemello You can find one from ebay or silmilar sites.
I know its to check their reliability.



But here is a reliable source I trust as best metal cutting tools provider.

www.bipico.com
02-13-2013 07:41 PM
Oldguy48 See if there's a local Do-All representative in your area. I was very fortunate to have one as a friend, and I ordered my bandsaw blades from him, for my Buffalo horizontal bandsaw (46 1/2" blades). They were excellent quality. This was quite a few years ago, but I'm sure there are still reps out there that would be glad to help you out.
02-13-2013 06:58 PM
boothboy Who every you buy from , buy a quality blade. I had continuous trouble with a horizontal band saw until I spent a fair amount of money on a quality blade. All the difference in the world.

BB
02-13-2013 06:47 PM
Old Fool
Quote:
Originally Posted by hduff View Post
I need to obtain a replacement metal-cutting blade for a 14" Wilton vertical bandsaw. The size I need is 3/8" x 92-1/2". The usual places like Harbor Freight, Northern, Sears? Or are there better (mail-order) souces?
Super Cut blades in Rathdrum Idaho make some of the best band saw blades out there. The number of choices they will throw at you will make your head swim. Their prices are very fair too. Give them a call.

http://www.supercutbandsaw.com/
02-13-2013 04:33 PM
machinee Try checking this : BandSaw Blades Online - Custom Welded Band Saw Blades . My dad purchased blade with them last week.
02-13-2013 11:44 AM
kso A while back, with a small shop, I had a lot of trouble getting right-size blades, and then often times the welds would snap. Got so aggravated I bought a blade welder for $900 and started just buying in coils...pricey but then you always have some. Guys would walk in and buy blades from me sometimes, I think I charged ten bucks plus blade material.

Any old metal shop that has an upright "Do-All" band saw will likely have a blade welder as part of the saw.

But, you can weld your own with gas or tig. The trick is to hold the ends aligned well, and anneal it afterward, just barely have about a half-inch section of it glowing a little, not red hot, then bring the heat down slowly. When it cools, bend it a couple times to test then grind off the extra weld. It's actually as reliable as the blade welder, just takes longer. Maybe you want to grind the teeth back a little in that area so that part is not having to cut.

Obviously the way for a guy just wanting one blade is a good supplier of pre-welded blades, I'm just throwing in some comments.
02-13-2013 09:05 AM
machinee There are sites that are do order to weld band saw blades.
11-20-2012 11:20 AM
timothale
make your own

one of my saws has an odd size blade so I make my own, I grind a bevel about 6 times longer than the blade thickness, then clamp them in a jig and silver solder them together, then off to the belt sander to sand the weld area and check thickness with a micrometer so it doesn't have a lump weld.
11-20-2012 12:57 AM
gearheadslife Welcome to Drills and Cutters | Drillsandcutters.com
11-19-2012 08:45 PM
monster76 Grainger or Dewitt tool for me
11-19-2012 08:41 PM
hduff Thanks guys. Had not thought of them.
11-19-2012 08:35 PM
OneMoreTime McMaster Carr

Sam
11-19-2012 08:26 PM
406 bug Try Grainger
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:37 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.