Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> any recommendation for good cheap nutsert rivet gun?
User Name
Password
lost password?   |   register now

Thread: any recommendation for good cheap nutsert rivet gun? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-28-2013 09:24 AM
S10xGN I ended up building a hydraulic tool which works with the 1/4", 5/16", & 3/8" riv-nuts and clips into my HF "port-a-power" system. Those larger (steel) sizes are a britch even with a good hand tool.

Russ
03-27-2013 04:22 PM
sedanbob I have one of the Harbor Freight ones - works just fine for the aluminum nutserts. Last couple of times I went there, they didn't have more nutserts, only the whole kit.
03-27-2013 04:13 PM
crownver Well I think that's a pretty good way too. The cuts in the nut are to grip the nutsert to keep it from turning, right? My way just relies on the friction of the nutsert in the hole, although once you have it started it's good. If the holes a bit big it might be a problem.
03-27-2013 03:32 PM
MARTINSR That's good stuff Crownver, it's a little more refined than my way.

I have installed them for years without a tool. For a 1/4" Nutsert you get a 5/16" nut, put it in the vice and with a hack saw put some small cuts on the surface of the nut like cutting up a pizza. You then get a 1/4" bolt put it thru the nut with the cut marks on the bottom so they hit the top of the nutsert and tighten it with your hand tight. Put the nutsert in the hole then hold the nut with a wrench while you turn the bolt with a ratchet. And yes this was on aluminum ones.

Brian
03-27-2013 03:02 PM
crownver You can do the aluminum ones without the tool. I tried the steel ones too but it was pretty tough. Just drill a hole the size of the bolt you'll be using into a piece of steel flat bar to use as a handle against the rivnut, and a nut on top of that to tighten down and expand the rivnut. The handle piece protects the rivnut surface and gives you a hard surface to turn the nut against.

You could probably do the steel ones with a longer handle piece and longer wrench. Use some lube under the nut.
03-27-2013 01:45 PM
35WINDOW When I was first learning about Rivnuts I went to HorrorFreight and bought one of thier kits that had Aluminum Rivnuts-it worked ok for light stuff, but then I decided that I wanted to put in Steel ones, so I bought them from McMaster Carr, and they offer a reasonably good Tool for putting them in-

I was making some support Rods with Rivnuts in them, and in a pinch I used the HorrorFreight Tool on a Steel insert-took a little more effort, but it installed them just fine-

I like the HorrorFreight style better (you can use one hand), but the McMaster Carr Tool is more robust-

Here's one from Hf:

http://www.harborfreight.com/3-in-1-...kit-94100.html

Here's the ones I bought from McMaster Carr:

http://www.mcmaster.com/#rivet-nut-i...-tools/=m2b6f8

edit: dang it, I can't pull up the indiviual pages on the McMaster website, but they offer different ones-I wuould buy the HF style if I were going to do it again, although any of them work just fine-
03-27-2013 01:19 PM
tech69
any recommendation for good cheap nutsert rivet gun?

Never used one and see them on line so am assuming a normal rivet gun would not work for this, right? Took off a mirror on a Cougar and the inserts kind of just fell apart so to speak. Even though it's not my duty to go run out and get one of these tools it seems like a handy one that's worth having.

Any cheap $30 range ones would be nice. Suggestions?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.