|04-14-2013 06:13 PM|
Increase all the jets till you get the best track MPH. and look at all the plugs
Then go back and retune the primarys part throttle as required.
The afr gauge is just a guide. (to avoid excessive lean)
You may be actualy cruising on the idle circuit. may have opened up the IFR a hair too much now.
|04-14-2013 02:17 PM|
BTW, just got home from the track. AFR is 12.7 under boost I think it's lean! But at 3500 cruise it is 11.5 so I think I am going to pull 4 numbers from the primaries and add 6 to the secondaries. What do you think?
|04-14-2013 11:45 AM|
Why not employ a WOT throttle switch to switch on the retard at say 1/2 to 2/3 throttle
Or a simple hobbs manifold pressure switch say 3psi so you don;t have to "remember"
|04-14-2013 11:12 AM|
The summit/Bosch 2 bar map sensor is half the price.
|04-14-2013 04:56 AM|
|04-13-2013 08:37 PM|
Adding a boost retard box will allow more idle and part throttle timing when not under boost
which will idle and drive nicer.
|04-13-2013 07:08 PM|
Well thought I would give you guys an update. I tore into the carbs today and used a borrowed set of numbered drill bits on the IFR's. I went one step larger, but I do not know what size. What I did was take the largest bit that would just slide through and then went up one size. Honestly, my eyes can't read numbers that small anymore. Started the car and the idle was of course a lot richer. Went about 1/8 turn closing on the 8 idle screws and got a 12.5 AFR smooth idle. At 2,000rpm now have 14.0 cruising and at 2,500rpm it is 14.7! Man I am damn happy now. Tip in and it goes to 13.0 and a little more throttle and it is 12.5 . I think this is just about dead nuts for a blower motor.
Thanks for everyone's help. Now I just have to get it to the track so I can do the jets and HSAB's. I think it's close, just on the rich side.
|04-03-2013 04:19 PM|
Car idled rough so I had to back all 8 mixtures screws out 1/8 more. No blower surge. Checked the AFR and Aha! A difference, although only .4 AFR. But the misfire at 2500 was reduced. Added one more strand to each bleed and now the IFR is down to 14.9 @ 2500.
Okay, I must have misunderstood this comment.
|04-03-2013 04:12 PM|
|04-03-2013 09:42 AM|
|spinn||Your idle air bleeds are causing a rich miss at 3000rpm?|
|04-03-2013 08:14 AM|
I just looked out the metering orifice sizes for that 650BC carb. To me it looks like the idle air bleeds are generous and the idle feed restriction is a bit stingy , on that carb. But I am not ready to tell you to start drilling etc yet.
(I am not that familiar with that specific carb model)
You can manipulate the idle air bleeds by hand while it is running by blocking /restricting flow with your fingers.
and read the AFR gauge @2500 and 3000 rpm. Then try the same with the high speed bleed, using a mirror too.
to see the main start up rpm.
Again verify no leaks (intake,blower and exhaust gaskets) and correct idle throttle position T slot exposure @idle FIRST
and correct base idle mix adjustment (not based on the AFR reading @ idle.)
|04-02-2013 09:16 PM|
Did you try just richening up the idle mixtures screws, First.?
Did you do the mirror test to see the rpm that main jet fuel flow starts at? It my be starting too late?
(high speed air bleed too big. (It doubles as a kill bleed)
The blower case must be warm before making any tuning evaluations.
( fine tune idle air bleeds by hand by soldering a pair up and drill with a 1/16" .062" drill bit, then hone by hand with the bit, as required, to fine tune the idle AFR.)
First thing to do is verify no vacuum leaks and No exhaust leaks. Leaky headers/gaskets will really screw up the idle/afr.
|04-02-2013 06:23 PM|
Here's the fun for tonight (I actually do enjoy carbs, they make me THINK!)
Took some 18 gauge wire and stripped it to individual strands (tiny). Put one strand in each idle air bleed and bent over the edge of carb so they would be held in by the air cleaners. Started car and warmed it up. Car idled rough so I had to back all 8 mixtures screws out 1/8 more. No blower surge. Checked the AFR and Aha! A difference, although only .4 AFR. But the misfire at 2500 was reduced. Added one more strand to each bleed and now the IFR is down to 14.9 @ 2500.
So I ordered the Proform kit that has bleeds from 65-75. Bet I'll be using the 65's but it is just a hunch.
I could probably up the primary jetting but I already have 79's in there and a 6.5 power valve. Hard to believe 650's would need more than that?
When I power brake it against the convertor the AFR drops to 10.5 so I am plenty rich already!
|03-31-2013 05:14 PM|
You only need to richen it up a bit. It won't surge.
Do not attempt to target a particular AFR at idle. Give it what it needs.
Surge at idle is real fat or real lean.
Do yu have a boost retard box? if so set the timing to 34BTDC and take timing out as boost rises, with the box.
|03-31-2013 03:38 PM|
Here's the deal. Had to lean the idle out to stop the blower surge. Screws are only out 3/4 a turn on all of them. Transfer slots are correct. Timing is locked at 28 degrees. Cam is 234/244 @ .050. Idle vacuum is 10 inches.
I get the feeling that if I could richen the idle I could solve the part throttle miss/surge but THEN the blower surge would come back?
|This thread has more than 15 replies. Click here to review the whole thread.|