Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Head identification and c.r.
User Name
Password
lost password?   |   register now

Thread: Head identification and c.r. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-20-2013 07:41 PM
El Rob Any one used the procomp heads yet. i have read a lot of good and bad. The bad seems to be small like valve covers not fitting right. I looked at them for some time at Skip White site.

Not trying to hijack you thread.
04-15-2013 11:30 PM
techinspector1 I'm getting some bad information from KB's site. Your SCR would be more like 9.55:1. I'm going to have to begin figuring this stuff myself instead of taking someone else's word for it.

Use a cam with intake duration somewhere between 205 and 220, with 212 as a middle ground.
04-15-2013 10:26 PM
fordss What cam should I use With that ratio ? I want to try to use my stock torque converter.The heads will only do as high as 550 lift . My car is 3300 lbs. Any help would be great
04-15-2013 01:36 PM
techinspector1
Quote:
Originally Posted by fordss View Post
1991 chevy 350 with stock pistons I believe dish pistons going to put procomp 58cc heads on. What would the compression ratio be.
If we figure the dish at around 12cc's (trying to be real here), the static compression ratio using 58cc heads on a 350 would be 10.3:1.
04-15-2013 01:05 AM
68NovaSS Your earlier post has been merged with this one.
04-15-2013 12:38 AM
68NovaSS Just get the information the form asks for and it will calculate your c.r., if you have dish pistons, need to know the volume of the dish in cc's, how far the piston is down in the hole at TDC, typically .025", compressed gasket thickness, typically .041", etc.

We could guess at about 9.5:1, but...
04-14-2013 10:44 PM
fordss Ok I was thinking of do procomp 58cc head 210 flow I just don't know what my compression ratio be. I do not know how to do calculator tool on the web. It is 1991 chevy 350 if some one could tell what it would be great
04-14-2013 10:31 PM
fordss Sorry I'm not that smart I have no idea how do that
04-14-2013 09:41 PM
1Gary Plug in the numbers:

RSR Static Compression Ratio Calculator
04-14-2013 09:24 PM
fordss
what will my compression ratio be

1991 chevy 350 with stock pistons I believe dish pistons going to put procomp 58cc heads on. What would the compression ratio be.
04-14-2013 04:25 PM
DoubleVision You don't want to use 193 heads. These are TBI "Swirl Port" heads. They give a engine real good low end torque and fuel economy, but due to the swirl port, they run out of breath at 3000 RPM.
04-14-2013 12:52 AM
mikesnyhere I used a 270 adv duration with 9.1 to comp. ratio it worked really well on a ported 302 . I would hesitate to use it on anything less than 8.8 . what is recommended ? the 268 is a high energy Crane ? their recommended specs should tell you a recommended CR , and if new springs are needed . best to look at what the cam manufactures suggests .
04-13-2013 09:46 PM
fordss Sorry guys, l found what the chambers size was. I don't know how to delete the post, but since it's still on; could l put a 268 high energy cam in it with these heads? Thanks
04-13-2013 09:45 PM
eight90 They are 64 cc give or take a cc. Others have cc'd theirs here and I cc'd mine as well, just to make sure.
04-13-2013 09:01 PM
fordss
Head identification and c.r.

Want to know what the chamber size of a chevy head, 14102193...As much as l looked up, l can't find the chamber sizes, l found the valve size. Any help would be appreciated thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.