Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> Need a recipe for a 427 Ford build
User Name
Password
lost password?   |   register now

Thread: Need a recipe for a 427 Ford build Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-26-2013 12:09 PM
CNC-Dude I built a 454 stroker that was featured in a Cobra magazine back in the 90's. It made 500 HP with medium riser heads with only mild porting. So you should be able to get that kind of power relatively easily.
04-25-2013 02:27 PM
oldbogie
Quote:
Originally Posted by Red Lehr View Post
Hello all ! I have a 64 Galaxie 500 2 dr fast back that I want to put a 427 FE Ford in. The block needs some boring maybe .30 over...I have a 390 in the car now with 428 CJ heads,RPM Performer intake match ported and a 750 Holley DP on top.I'm not wanting originality ,just a nice engine with a healthy growl.
I was thinking of possibly stroking it with a 428 crank or 4.25 scat crank.I could save money by using the CJ heads or should I find some low riser heads, aluminum heads ?? I have a Richmond Super t-10 tranny with a 9 inch 380 rear end .
My budget is moderate,I've been saving for this one.
I am a newbie at turning wrenches,but I'm learning....I have a friend close by who is an engine builder and has a machine shop.
Thanks for any feedback in advance ! It's great to be in this forum !!
Red
If your budget is up to it Blue Thunder or Edlebrock aluminum heads (in that order) are well worth the power output improvement and weight reduction for the FE.

The factory heads have pretty poor combustion characteristics and not much tolerance for contemporary un-leaded fuels. These aftermarket heads bring the Ricardo heart shaped combustion chamber (as much as the FE will allow at least) which really pumps up the action and improves all around performance by getting the level of efficiency well up for this engine. The closest head to these from the factory is that used only on the 1960, 360 horse 352. After that for some reason Ford abandoned combustion efficiency for more breathing. Not that more breathing isn't good; but you also need good combustion. Ford, like most everybody else, hung their hat on covering poor use of the fuel and air that got into the engine with super high compression ratios and lots of 100 plus octane fuel. That worked OK when that high octane leaded gas was thirty cents a gallon, it's not much of a solution today.

Bogie
04-23-2013 06:59 AM
Mr. P-Body We've done a few "454" Fords. That is, the 427 block, .030" over and the 428 crank. Pistons are available from Icon. Highly recommend the "BBC" rod change.

The CJ heads will make plenty of streetable power and torque (in the lower and mid-range).

Jim
04-22-2013 10:58 PM
vinniekq2 power expected? life expectancy of super t-10?
04-22-2013 10:47 PM
Red Lehr
Need a recipe for a 427 Ford build

Hello all ! I have a 64 Galaxie 500 2 dr fast back that I want to put a 427 FE Ford in. The block needs some boring maybe .30 over...I have a 390 in the car now with 428 CJ heads,RPM Performer intake match ported and a 750 Holley DP on top.I'm not wanting originality ,just a nice engine with a healthy growl.
I was thinking of possibly stroking it with a 428 crank or 4.25 scat crank.I could save money by using the CJ heads or should I find some low riser heads, aluminum heads ?? I have a Richmond Super t-10 tranny with a 9 inch 380 rear end .
My budget is moderate,I've been saving for this one.
I am a newbie at turning wrenches,but I'm learning....I have a friend close by who is an engine builder and has a machine shop.
Thanks for any feedback in advance ! It's great to be in this forum !!
Red

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.