Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Amp gauge
User Name
lost password?   |   register now

Thread: Amp gauge Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-26-2013 10:02 PM
Originally Posted by Rick 5150 69 View Post
You may be able to buy a volt meter to match the panel from Classic gauges...
1958 Chevy Apache Classic Instruments Gauge Cluster Install - Custom Classic Trucks Magazine
Exactly!!! get rid of the AMP gauge... notice NO new cars have one. Used to be that if the AMP gauge blew you were stuck. Get a volt meter that can connect to anything with voltage. AMP gauges are things of the past...
04-26-2013 07:44 PM
no no

Are taking pictures at 100 mph?
04-26-2013 02:05 PM
ogre here the truck is running down the road and the gauge is reading 14 volts at the center dot
lots of good 55-59 chevy truck builds over on the site you should be over there too

04-26-2013 02:01 PM
ogre i did a write up on how to change an amp meter to a volt gauge in a task force truck over on the 67-72 truck forum
i have a build thread over there look for post 36

i used the stock gauge face and inserted the guts from a 2'' volt gauge into the stock cluster
here the truk is off and voltage is zero, i installed the needle to be on the middle dot when the voltage is 14 volts

04-25-2013 10:04 PM
ohms law

There is no question that the voltmeter is the gauge of choice as compared with the ammeter.
Some of the statements here on the HRBB about ammeters, however, are incorrect. Including Madelectrical.
While it is correct that some Manufactures (Chrysler) did route the full electrical load (current) through the ammeter, GM did not. Don't know about Ford. Who cares.
All the data I have seen indicate that GM used the main accessory wire as a shunt and measured the voltage drop (IR) across this wire to drive the ammeter. It's ohms law stuff.

04-25-2013 07:46 PM
75gmck25 Full current amp gauges were fairly common in older vehicles, but the output of alternators was also usually quite low (about 40 amps or less). As alternator amperage increased, the in-dash amp gauges were changed to a shunt-type amp gauge, which does not flow the full current through the wiring.

An amp gauge that uses a shunt under the hood (used by GM in the 70's) works more like a milli-voltmeter that measures the voltage drop between two points in the wiring harness. The gauge then uses the measurement of voltage drop to calculate an amp (or current flow) reading on the gauge. Its similar to measuring the amount of fuel in your gas tank at two points in time. If you know the amount of time and the fuel level difference between the two measurements, you can calculate the fuel flow rate.

The article referenced in a previous post by Rick 5150 69 identifies a replacement cluster that uses a voltmeter instead of an ammeter. This is a much safer choice.

04-25-2013 04:46 PM
41 Buick custom
Amp gauge

There are diagrams to show you how to wire it up. Amp gauges we're in cars for a lot of years. If they weren't safe the factory wouldn't have used them. You have full power going in to run your fuse box anyway. All a amp gauge is a big fuse with a shunt in I, draw to many amps and it will shut down.
04-25-2013 03:58 PM
Rick 5150 69 You may be able to buy a volt meter to match the panel from Classic gauges...
1958 Chevy Apache Classic Instruments Gauge Cluster Install - Custom Classic Trucks Magazine
04-25-2013 03:44 PM
poncho62 Trouble with an amp gauge is that all the cars current must go through it to get a proper reading. That means taking a main wire through the amp gauge.....A volt meter just monitors the voltage, so a feed from almost anywhere will tell you your charging system is working....I would just install a voltmeter if I were you.
04-25-2013 03:13 PM
AMP gauges at the dash are troublesome.
They should be by-passed, and then install a VOLT gauge.

Wether or not you agree itīs worth reading.
04-25-2013 03:08 PM
Amp gauge

1958 Chevy Fleetside with original gauge cluster with 350 sbc, one wire 100 amp alternator, HEI distributer and electric motor fan. When the electric motor fan kicks on it would send the amp gauge from the middle of the gauge to the far right. This let me know my fan was on and that my alternator was putting out current. I rewired the entire truck with an EZ Wire kit and have either overlooked it or it did not come with a wire for the amp gauge. The amp gauge has several connectors on the back of it and I don't know what wires it takes to get it going again,,,,,, any suggestions?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 05:30 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.