Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Fresh engine won't run - I'm stumped.
User Name
Password
lost password?   |   register now

Thread: Fresh engine won't run - I'm stumped. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-20-2013 07:45 AM
Dougie Update. I haven't driven it because the front clip is off, but it seems to be running great now. I adjusted valves one by one using the method that puts the lifter on the bottom of the lobe. I also got the timing dialed in at 20 degrees BTDC initial and it all comes by 2500 rpm (36 degrees). Starts right away and it idles with a nice lope at about 900 rpm. I can wait to drive it! Thanks for all the help.
05-05-2013 05:40 AM
64nailhead Great news, I've been following this thread. I'm sure you were second guessing everything you had done when building this. I've been there myself (I can imagine that most everyone has at some point as well.)

The 1st time I had the same exact problem you had, quite a long time ago, I ended up using a timing light while cranking. I had the same issue, off by one cylinder on distributor installation. Since then, I use a timing light on initial startup. It definitely eliminates all of the guessing of what exactly is happenning.

Good luck with your project!
05-04-2013 08:23 PM
Dougie YES!!! I got it running. I readjusted the valves using the up and down method on the pushrod and not spinning it. Now that I've done it both ways I can see how the spinning method could be misleading. More importantly, I think the real issue was the timing. I was trying to start it around TDC because that's what many posts said should work to get it going. It started but ran very rough. I immediately advanced it quite a bit and it smoothed out. After warming up, it seemed to like about 12-14 degrees BTDC.

Ran it for 25 minutes between 2000 and 2500 rpm in the garage with a box fan in front of the radiator to break in the cam. The whole time the oil pressure never fell below 45 lbs. and the temp never rose above 200 degrees, so I feel really good about this, and no leaks.

Next change the oil and filter and run a little more before putting the front clip on so I can take it for a spin. Thanks everyone!
05-02-2013 03:08 PM
Too Many Projects
Quote:
Originally Posted by Dougie View Post
Someone needs to close his gap. (For the record, plug gaps are fine)
if the pistons hit the plugs and closed the gap, there is more than just a timing issue going on. I've NEVER had a backfire affect plug gap either. What is he smokin' ???
05-01-2013 09:19 PM
bygddy And do you have the pn# for the cam handy? Perhaps a stupid question but you didn't end up with a 5-7 swap or anything?A
05-01-2013 09:15 PM
bygddy Try dropping a touch of oil down the plug holes and then confirm your dist is right, and start over. I'm wondering, and could be dead wrong, but if you had exsessive cyl wash and have no compression on multiple holes it would run as poor as you described or not at all. You mentioned you had seen fuel, I'm just wondering if it was too much on fresh walls and rings and its not sealing worth a damn.
05-01-2013 08:54 PM
Dougie Someone needs to close his gap. (For the record, plug gaps are fine)
05-01-2013 07:48 PM
bygddy So am I the only one who found the last 5 posts (nope, not spinn's) more then slightly creepy?
04-30-2013 10:30 AM
spinn The engine wont start and you came up with the plug gap closed? Yeah , that will do it but he confirmed spark.
04-30-2013 09:25 AM
Hot Parts Check plug gap. Pistons may have come up & closed them. I did this on a high compression motor once $ it does fire & then dies. I also was confused at time until I found it out.Gods love be with you.
04-30-2013 08:23 AM
496CHEVY3100 You use a priming tool to fill the lifters and prime oil to the bearings so it wont have a dry start and destroy bearings and cam, if you prime it first you can adjust rockers with valves closed until contact with rocker + 1/4-1/2 turn Chevrolet recommends 1 full turn with GM lifters and cam,but there cam is rated a 6 and after market is rated at ,50 so if you use gm recommendation on aftermarket can vales will be to tight it will cause low vacumn or no start .But if lifters are DRY NOT pumped up it takes1-1/4 rounds to bottom a lifter from first point of contact so if you bottom out lifter then back it up 3/4 round you are at 1*2 round down THEN you use a priming tool to fill lifters until oil comes out all rockers ,while priming turn engine 90 degrees to alow oil to all passages this is the most accurate method since there is no guessing or you can use a dial indicator or your method which ever you choose ,I would use the one that you like best ,I was just giving you an option ,but on hundreds of racing engines and mant street engines i have never had but one flat cam,dont think it was due to miss adjusted valves.These are a couple of championship cars the #76 Modified ,#3Limited class,66 a hobby stock rebuild only,77 crashed before season end.
04-29-2013 11:16 PM
spinn Yeah if you bottom them out with just a turn back, how will they pump oil up to fill. That plunger acts as a suction pump to pull oil into the lifter.
04-29-2013 07:34 PM
64nailhead
Quote:
Originally Posted by 496CHEVY3100 View Post
Yes ,If both intake and exaust are closed.and lifters are pumped up,,, if not adjust the rocker down until it bottoms out the lifter then back it up 3/4 round.
No disrespect meant, but are you kidding?
04-29-2013 07:13 PM
richard stewart 3rd Hi
I'm sorry for not being clear on the subject.
The intake & exhaust on each cylinder your
doing do get adjusted at the same time.
I will be more careful in the future.
Rich
04-29-2013 11:01 AM
techinspector1 It may be possible for a rookie to have the finger and thumb "feel" necessary to use the "spin the pushrod" method and get the valve adjustment correct, but 99 times out of 100, the valves will end up too tight as related above. Please read through this tutorial and implement its instructions. It's pretty much bulletproof and I have received PM's from many fellows saying so....
http://www.crankshaftcoalition.com/w...stment_SBC/BBC
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:43 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.