Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> engine angle
User Name
Password
lost password?   |   register now

Thread: engine angle Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-02-2013 06:21 PM
techinspector1 The motor/trans unit can be positioned anywhere in the engine bay to miss other components such as steering, brake booster, etc. You have to keep the centerline of the crankshaft perpendicular to the centerline of the rear differential, but other than that, the package can go most anywhere you want it to. '60's/'70's Mopars sometimes had the package as far as 3" to the passenger side to clear other components such as valve cover to brake booster clearance, so don't think it has to go right down the middle. It doesn't, as long as there is breathing room for the bellhousing and transmission in the driveshaft tunnel. And even that isn't sacred. You can cut some sheetmetal out to make the whole mess work if you need to, then weld it back in after the swap is complete. Just leave enough clearance between any part of the motor/trans and any sheetmetal to prevent contact and subsequent noise in the passenger compartment. The motor/trans must be segregated from the sheetmetal of the truck by rubber or urethane mounts at all locations. Rubber is better in my opinion, not so harsh.

One more thing, good engineering practice dictates running the exhaust out to the rear bumper. Terminating it under the truck will create a droning in the truck sheetmetal that will make you crazy in short order. Install an "X" or "H" balance pipe before the mufflers for a more pleasing tone and slightly better performance/mileage.
05-02-2013 06:08 PM
sedanbob Ideally, this should be calculated with the vehicle at ride height, front and rear. Since you mentioned you will be changing the rear differential, if you plan to change the height of the rear suspension, try to have the rear of the car where you intend it will be after your changes.
05-02-2013 01:44 PM
oldbogie
Quote:
Originally Posted by f1 crazy View Post
HI my name is Craig, I have a 1952 f1 that I am installing a 351 w in I have the engine and transmission sitting in there with aftermarket crossmembers looks good, how do I figure out the angle or what does the angle need to be at, I will be installing a new differential too. can anyone help me?
You need to get the carb level, if using one. That means mocking up the installation with the intake your going to use and leveling the carb pad front to rear and left to right.

Bogie
05-02-2013 01:04 PM
f1 crazy
engine angle

HI my name is Craig, I have a 1952 f1 that I am installing a 351 w in I have the engine and transmission sitting in there with aftermarket crossmembers looks good, how do I figure out the angle or what does the angle need to be at, I will be installing a new differential too. can anyone help me?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:16 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.