Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> Convertible top binding is puckering
User Name
Password
lost password?   |   register now

Thread: Convertible top binding is puckering Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-11-2013 07:08 AM
DanTwoLakes Nice job. It turned out a lot better than the first time.
05-10-2013 06:14 PM
ddriver
Thanks guys...finally finished!!!

Dan and Jalopy...thanks for all of your advice. Dan - we made some tension springs and cable which work great in holding the sides 'taut' while cruising down the road. Realized that my relief cuts weren't close enough to the edge and that is why my test pattern came out wobbly. Jalopy, ended up just putting a welt around the window and made the window a bit larger - which helps with visibility too!!!! It took all the puckering out of the back Posting a couple of pictures of the finished top. It was an interesting process making a top from scratch with no patterns or old tops to look at. The boyfriend is a happy camper and I'm happy that we won't get drenched like rats next time we get caught in the rain - no fenders equals lots of spray inside the cab.
05-09-2013 06:57 AM
DanTwoLakes That's very good advice. Making the fabric stiffer around the window opening would make it easier to bind.
05-09-2013 02:06 AM
Jallopy Here is another sugestion

I did my window a little different .
I made a hem on the out side from the classic fabric by turning the edge under .



On the inside it was recomended to make a large one piece gasket to go all the way around the window which I did.
I had to add another half metre to my order to make sure I had enough material now. (It costs me $160 /m for the fabric)

05-01-2013 04:45 AM
DanTwoLakes Do you know if this binding fabric is woven or not? If not, you should find some binding made of bias cut woven acrylic like Sunbrella. The bias cutting may not help much for the tight corners, but it will surely help the edge over your door window. Also, a binding attachment for your sewing machine is not a bad idea either. Sailrite has all the Sunbrella bindings. Give them a call, maybe they have other ideas for you.
04-30-2013 08:33 PM
ddriver Thanks Dan...you're right, the oval for the window is only 17x5 1/2 so the curves are a little extreme. Maybe a rectangle instead of the oval...that would take care of the issue on the back curtain. I don't have anything under the sides right now, maybe bowpads would help. The binding is a 1-inch double fold acrylic binding from Rexpegg. It's pretty stiff (think it is pre-treated for water resistance). As always, you have great ideas. Posting a picture of the binding.
04-30-2013 05:42 PM
DanTwoLakes In the first two pictures, the main problem is the curves are very severe. It won't matter what binding you use, the binding on those tight curves will always do that. I don't know what the problem is on the last picture, that should have worked out fine. What is the binding made of? Do you have any padding under the outside edges that curve down? If you don't, eventually you will have wrinkle problems on the main top there too. Regular convertible tops have cables that hold the curve taught and also prevent the top from getting damaged by the air flow while driving.
04-30-2013 12:59 PM
ddriver
Convertible top binding is puckering

Building a convertible top for the '29 and having a bit of a binding issue. Straight lines look great, but any curved area wants to pucker. Is it due to the binding not being 'bias cut'??? Using 1" double fold binding. Pictures are mock-up materials, not using the Stayfast material yet. Dont want to waste $65/yd material trying to get the patterns laid out. Side panels and back curtain area where the window will be sewn in are the areas that I'm concerned with. Should I try to find a few yards of bias-cut binding? Any advice is appreciated. Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:57 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.