Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> 66 impala stock suspension height?
User Name
lost password?   |   register now

Thread: 66 impala stock suspension height? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-15-2013 07:44 PM
grandslam1991 Thanks for the help! What would be a good brand to go with for springs?
05-15-2013 09:43 AM
Originally Posted by grandslam1991 View Post
How is it if I buy "stock height" springs then why would they not sit where they're supposed to? .
'Cause the guys winding springs in some spring shop in 2013 might not be hitting the same spec as the factory back when, and they also have looser interchange standards. Crap shoot...old cars, ya gotta live with it.

Yes, lowered a-bodys don't drive well either. I have an El Camino that was very-slammed for about five years. I got sick of it right about the time the front crossmember wore through.
05-14-2013 09:13 PM
grandslam1991 How is it if I buy "stock height" springs then why would they not sit where they're supposed to? And as far as low riding goes, this car is WAYYY to low! I bottomed out the trans pan already as well, and it's a miracle I didn't ruin the trans at the same time. It is so impractical and I drive this car daily.
05-14-2013 09:08 PM
grandslam1991 I will post pics tomorrow once I get a chance to pull the wheels off
05-14-2013 08:22 AM
kso Most a-arm suspensions will, from the factory, have the lower arms pointing just a little downward from level (meaning the car is about an inch or so higher than it would be at the point where the lowers were level, and sight that from the pivot points not the a-arm shape). You'd have reasonable clearance and that puts the roll center up around the crankshaft centerline so the car won't pitch or dive around in corners.

You'll need to change the springs, spacers are available but nothing I've used seem to stay in place. Coils commonly interchange among GM cars, just measure wire diameter, loop diameter and height and expect to take a couple trys to get it right. Most will say get new ones but that doesn't guarantee the car will come up the right amount either, the first time.

Rears, same deal.

But you won't be able to cruise around humming Low Rider anymore. Think about might miss it.
05-14-2013 07:46 AM
RWENUTS PIcs man!! Shoot us some side view pics.
You might need to buy new springs!
05-13-2013 08:52 PM
66 impala stock suspension height?

Hey all I've got a 66 impala 2 door hardtop and I'm trying to get me some info on the stock suspension height. The car seems to sit way closer to the ground then it should, and I have long tube headers on the car that bottom out frequently. However I'm not sure what the ride height should be. I had the car in for a wheel alignment and they told me the previous owner cut the springs or something to lower it. So my question is how can I determine how much it's been lowered? And how can I correct it to stock height? Will I need to correct the rear suspension as well?... Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 03:57 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.