Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Hotrodding Basics> transmission and pinion shaft mis-alighnment
User Name
Password
lost password?   |   register now

Thread: transmission and pinion shaft mis-alighnment Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-25-2013 09:34 AM
1971BB427 No reason to get excited. Even a couple inches right or left wont mean a thing. If it was an issue, then you couldn't have a driveline that ran uphill to the trans either. As mentioned, stock Fords have been this way for many decades.
05-25-2013 08:23 AM
S10xGN I'd be more concerned about the tires being offset than the pinion. Neither will "hurt", but one will look like dammit while the other will never be seen...

Russ
05-25-2013 08:18 AM
MARTINSR Is the rear end centered in the frame? How in the living hell does someone do this, does he not have a measuring tape? You should buy him a measuring tape so he doesn't do this to the next guy.

Brian
05-25-2013 08:16 AM
joe_padavano The output shaft and pinion shaft are offset up and down normally. There's no difference between an offset in that direction and an offset side-to-side. What IS important is that the two shafts need to be parallel.
05-25-2013 07:54 AM
Crosley No idea why this is in "site suggestions & help" forum... moving to basics forum
05-25-2013 07:19 AM
timothale
Ford GT ?

The first new Ford Gt ( Modern version of the old GT 40 ) had the rear of the body tilted up and the rear half shafts have a lot of off set from the Dif out to the wheels. I was used to looking at corvette and Jag Irs and spotted it right away.
05-25-2013 05:30 AM
BOBCRMAN@aol.com Should not be a problem. Ford motor company has used offset pinion rear ends since the fifties with no bad effects.
05-25-2013 12:32 AM
GARY HOOTEN
transmission and pinion shaft mis-alighnment

Now that I have my frame done and the rear 4 bar suspension and axle installed, I discovered that my welder installed my 4 bar axle brackets one inch and an eighth to the left. Now that my pinion is one and an eighth inch to the right of center, begs the question among others. Does the trans. shaft and pinion have to line up straight on laterally or is there an excepted amount of ms-alignment ?
I measured from end to end for the degree angle, and it came out 1.5 degrees.
I could move the drive train over to the right this amount, but buying new brackets and having them re-welded would be less of a hassle.
Your help here would be greatly appreciated, Thanks, Gary

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.